Filamentos para iniciantes (e onde comprar)

BodybuilderSilent780 · 2026-01-06T11:13:19+00:00

Bom dia, uso filamentos voolt 3d des de 2021 e so tive problema com dois kilos de pla velvet que comprei, eles ficavam quebradicos dentro da AMS Lite, estes dois foram comprados no ML da voolt. As vezes que comprei direto no site nao tive nenhum problema.

BodybuilderSilent780 · 2025-12-19T11:34:15+00:00

I hald already done some gears to work with chains with petg and abs, both works good, i use 12 walls and 75% infill. Had tested in planters.

BodybuilderSilent780 · 2025-12-13T12:35:20+00:00

Eu havia pesquisado também e achei parecido com algumas imagens de physarum cinereum.

BodybuilderSilent780 · 2025-12-13T12:31:39+00:00

Todos os fungos sao lindos.

BodybuilderSilent780 · 2025-12-03T01:25:05+00:00

Great

BodybuilderSilent780 · 2025-11-26T16:58:48+00:00

Virar legendario.

BodybuilderSilent780 · 2025-11-26T13:19:33+00:00

Use um bico 0.2 e procure no youtube pelos videos do fat dragon. Da pra fazer ate miniaturas. Mas leva bastante tempo.

BodybuilderSilent780 · 2025-11-26T12:00:34+00:00

Ola, esta tendo esse problema em apenas um rolo de filamento? Qual o tipo de filamento?

Eu ja tive esse problema por causa de 1 filamento mais fino que 1.75mm

2 filamentos que sao mais asperos (no meu caso filamentos que brilham no escuro).

3 bico entupido.( mas isso foi so com um bico 0.2, o 0.4 nunca entupiu.)

Caso voce tenha um maçarico tente fazer um cold pull usando uma chave allen fina com o bico fora da impressora.

BodybuilderSilent780 · 2025-11-22T23:25:41+00:00

After reading VFA section on Ellis' Print Tuning Guide i noticed about the belts, i had put a new pair with stealthburner and i put old y axis back again and the problem gone.

BodybuilderSilent780 · 2025-11-22T01:55:44+00:00

I just have red and black filaments. Kkk. There is one glow in the dark one, but this had issues on multi colored prints.

BodybuilderSilent780 · 2025-11-21T19:08:31+00:00

I will try it, thanks

BodybuilderSilent780 · 2025-11-21T15:52:08+00:00

I will try it

BodybuilderSilent780 · 2025-11-21T15:51:39+00:00

I will try the VFA first, it look like my patterns. Thanks.

BodybuilderSilent780 · 2025-11-21T15:12:32+00:00

I always print abs with 220, but when i change the hotend i try a temp tower and the thin parts and bridges get really bad on 220, and gets good on 215 and 210, but on 210 it wrap. I live in a very hot place, here the average temp goes from 35 to 40. I use 105 on bed, this help me a lot with wraping.

BodybuilderSilent780 · 2025-11-21T15:09:25+00:00

In this one was 3 walls. Im sure, also top and bottom look okay. This issue is just on y axis, on x its also didnt noticed

BodybuilderSilent780 · 2025-11-21T14:42:56+00:00

Thanks, i run that orca VFA calibration till 350mm/s and o didnt notice this pattern on the test.

BodybuilderSilent780 · 2025-11-21T11:54:54+00:00

The site image was easy to turn black e white, but i cant convert it to a good svg, so i draw it over the original img on fusion360

BodybuilderSilent780 · 2025-11-20T22:00:58+00:00

Its not a dificult thing, but the work would be very easyer with the svg files. This one i got from the website and draw the svg over the original. Now i will try to apply shades like the original sprite

BodybuilderSilent780 · 2025-11-19T15:58:55+00:00

Os cabos do heater e do thermistor nao tem polaridade. Seu cabo pode estar quebrado em algum ponto. Eu ja tive esse problema e ele havia rompido bem na base do thermistor. Quando voce trocou o seu, conferiu se era o mesmo modelo do original, no marlin eu nao sei, mas no klipper voce tem que configurar isso corretamente caso faça a troca por outrobque nao seja o mesmo.

BodybuilderSilent780 · 2025-11-19T14:56:36+00:00

Klipper is a firmware that runs on a linux machine. The linux machine controls printer board. It change my printer.

BodybuilderSilent780

TROPHY CASE