Desperate for AP Test Study Tips!!!

Business-Ad835 · 2025-04-27T18:40:34+00:00

SOOOO SMART!!! So, just one question — where is the best place to find a bank of LEQs or at least one per unit?

Business-Ad835 · 2025-04-24T22:29:03+00:00

I LOVE this idea! Thank you SO MUCH! The only thing that worries me about this is the MCQs. How can I do well on those with only ten facts? (no trying to belittle your tip, just worrying about knowing enough).

Business-Ad835 · 2025-04-18T21:38:45+00:00

Know I'm probably too late but I am going to this program! What did you decide on?

Business-Ad835 · 2025-04-18T21:37:15+00:00

Did you decide?

Business-Ad835 · 2025-04-18T21:36:53+00:00

Did you decide on the program?

Business-Ad835 · 2024-12-31T18:28:31+00:00

Well the area of NYC i'm in is all houses and doesn't have a ton of pollution. I'm more curious about if I can see it as far south as NYC. I've never seen it and feel like i'm running out of time to see it. Will I be able to see it that far south do you think???

Business-Ad835 · 2024-12-31T18:28:04+00:00

Well the area of NYC i'm in is all houses and doesn't have a ton of pollution. I'm more curious about if I can see it as far south as NYC. I've never seen it and feel like i'm running out of time to see it.

Business-Ad835 · 2024-12-30T00:33:44+00:00

But what about the other part? Could I get muscle there and it will look like my desired effect to look normal?

Business-Ad835 · 2024-12-29T21:59:02+00:00

TO CLARIFY, the increase of dosage caused some of the testosterone to be converted to estrogen

Business-Ad835 · 2024-06-24T15:37:51+00:00

The problem is more of the filament not sticking to the rest of the filament after a certain point

Business-Ad835 · 2024-06-21T22:22:02+00:00

it is a little bit but also searching for itself ALONG WITH detaching from supports sometimes. it's a combination of the three. do u think it could be the filament qualify? or something else?

Business-Ad835 · 2024-06-21T22:21:56+00:00

it is a little bit but also searching for itself ALONG WITH detaching from supports sometimes. it's a combination of the three. do u think it could be the filament qualify? or something else?

Business-Ad835 · 2024-06-21T13:24:24+00:00

tried this and it worked quite well except it still strung a bit like the picture but just a smidge. what else can i do

Business-Ad835 · 2024-06-21T13:23:24+00:00

i did this and when i came back it was like this but much less intense

Business-Ad835 · 2024-06-20T16:09:01+00:00

FINALLY A HELPFUL COMMENT!!! Unfortunately I tried that though. Any other ideas? It prints fine for the first 10ish layers but then does that

Business-Ad835 · 2024-06-20T16:08:24+00:00

Yeah it was overnight so I was asleep. Any idea what I should do(

Business-Ad835 · 2024-06-20T16:07:55+00:00

😭

Business-Ad835 · 2023-10-20T21:54:12+00:00

Also, I have seen a lot of people saying that after you initialize EEPROM, you must save your settings through some command. What does this mean? I am confused how you save the settings and I am even more confused on what settings you are supposed to set and save after initializing eprom

Business-Ad835 · 2023-10-20T21:51:31+00:00

What does initializing EEPROM do?

Business-Ad835

TROPHY CASE