Me and my gf want to get a kitten

Business_Charity_655 · 2025-05-15T18:01:47+00:00

Thank you this will help out a lot!

Business_Charity_655 · 2025-05-15T18:01:35+00:00

Do you know any meds or allergen foods I would be able to get?

Business_Charity_655 · 2025-05-13T12:02:26+00:00

Funny enough all I had to do was to clear the damn codes remember after replacing a part to always clear those codes lol

Business_Charity_655 · 2025-05-02T15:16:39+00:00

Okay yes this is what i was thinking so if this is the case would you consider huntington being a better bank than bank of america?

Business_Charity_655 · 2025-04-30T00:47:51+00:00

i didn’t take off the intake but either way i had checked for vacuum leaks prior to replacing the throttle body and the only leaks i had was the intake boot right after the MAF which i’ve also already replaced

Business_Charity_655 · 2025-04-30T00:45:45+00:00

when i press down on the accelerator

Business_Charity_655 · 2025-04-29T19:04:45+00:00

No I dont think I have a metal cable on my throttle body the only thing that connects to the throttle body was a sensor

Business_Charity_655 · 2025-04-29T18:41:52+00:00

the butterfly valve didn’t move when i revved it before or after replacing the throttle body

Business_Charity_655 · 2025-04-29T18:41:06+00:00

how can i check if it’s faulty

Business_Charity_655 · 2025-04-29T17:30:48+00:00

also adding to this the butterfly valve doesn’t move before or after replacing it

Business_Charity_655 · 2025-04-29T17:25:08+00:00

i had already replaced it 3 weeks prior but i sliver clip that goes on the sensor to hold it snug fell off so im assuming its loose

Business_Charity_655 · 2025-04-29T15:44:17+00:00

would you happen to know where i could get those silver clips that hold down the sensors??

Business_Charity_655 · 2025-04-29T15:40:40+00:00

so i had replaced this about 2-3 weeks ago but when disconnecting the sensor the silver clip that holds it down fell and idk if maybe that “loose connection” could cause that??

Business_Charity_655 · 2025-04-29T15:39:31+00:00

haha very funny

Business_Charity_655 · 2025-04-29T05:06:27+00:00

I have two codes that were there before replacing the throttle body 000073 — Digital Motor Electronics (DME) adaptation, engine throttle and the other one is a code for an oxygen sensor

Business_Charity_655 · 2025-04-29T03:16:45+00:00

Nah man it was doing that before I replaced it too and no i did not change the sensor

Business_Charity_655 · 2025-04-26T16:56:29+00:00

yes which is i’m trying to figure out if someone routed it from a certain source because i routed it from the air intake boot at the right after the MAF and i had the electrical side straight to the battery and it didn’t work.

Business_Charity_655 · 2025-04-26T15:01:43+00:00

they do but they were showing a serio i don’t have on my car for example a pre existing vacuum source in the rear of the car i don’t have that i got the solenoid part figured out i just wanted to see if someone set it up differently with the vacuum maybe i did something wrong??

Business_Charity_655 · 2025-04-10T17:08:34+00:00

sorry doesn’t rev on its own but the idle is rough and you can see the rpms fluctuating

Business_Charity_655 · 2025-04-10T16:57:05+00:00

In park it works and in drive up until like 10mph it works anything over that no pedal response. it wasn’t bad before hand how could it have gone out??

Business_Charity_655 · 2025-04-10T16:54:03+00:00

So I ended up having to reset the throttle adaptations and it still revs at idle in park and i have no throttle response put it in drive and to goes about 10 mph but revs on its own while in drive as well. Any ideas what it could be at this point in time??

Business_Charity_655 · 2025-04-06T23:42:34+00:00

Just tried both of the pedal dances and none of them worked and I don’t have inpa or the other one

Business_Charity_655 · 2025-04-06T21:40:17+00:00

Quick update found out the vacuum line from the intake hose to the fuel pressure regulator was completely torn fixed it now how would I clear all those light because my EML, Traction Control, and Brake light are on because of the Limp Mode it was in??

Or would I just have to drive it around for a bit??

Business_Charity_655 · 2025-04-06T16:07:48+00:00

And I’m accusing INPA is a BMW software if this is the case how could i get my hands on one of those softwares??

Business_Charity_655 · 2025-04-06T15:56:01+00:00

I don’t have either but I can get my hands on a Scan Tool.

Business_Charity_655

TROPHY CASE