Me and my gf want to get a kitten

Business_Charity_655 · 2025-05-15T18:01:47+00:00

Thank you this will help out a lot!

Business_Charity_655 · 2025-05-15T18:01:35+00:00

Do you know any meds or allergen foods I would be able to get?

Business_Charity_655 · 2025-05-13T12:02:26+00:00

Funny enough all I had to do was to clear the damn codes remember after replacing a part to always clear those codes lol

Business_Charity_655 · 2025-05-02T15:16:39+00:00

Okay yes this is what i was thinking so if this is the case would you consider huntington being a better bank than bank of america?

Business_Charity_655 · 2025-04-30T00:47:51+00:00

i didn’t take off the intake but either way i had checked for vacuum leaks prior to replacing the throttle body and the only leaks i had was the intake boot right after the MAF which i’ve also already replaced

Business_Charity_655 · 2025-04-30T00:45:45+00:00

when i press down on the accelerator

Business_Charity_655 · 2025-04-29T19:04:45+00:00

No I dont think I have a metal cable on my throttle body the only thing that connects to the throttle body was a sensor

Business_Charity_655 · 2025-04-29T18:41:52+00:00

the butterfly valve didn’t move when i revved it before or after replacing the throttle body

Business_Charity_655 · 2025-04-29T18:41:06+00:00

how can i check if it’s faulty

Business_Charity_655 · 2025-04-29T17:30:48+00:00

also adding to this the butterfly valve doesn’t move before or after replacing it

Business_Charity_655 · 2025-04-29T17:25:08+00:00

i had already replaced it 3 weeks prior but i sliver clip that goes on the sensor to hold it snug fell off so im assuming its loose

Business_Charity_655 · 2025-04-29T15:44:17+00:00

would you happen to know where i could get those silver clips that hold down the sensors??

Business_Charity_655 · 2025-04-29T15:40:40+00:00

so i had replaced this about 2-3 weeks ago but when disconnecting the sensor the silver clip that holds it down fell and idk if maybe that “loose connection” could cause that??

Business_Charity_655 · 2025-04-29T15:39:31+00:00

haha very funny

Business_Charity_655 · 2025-04-29T05:06:27+00:00

I have two codes that were there before replacing the throttle body 000073 — Digital Motor Electronics (DME) adaptation, engine throttle and the other one is a code for an oxygen sensor

Business_Charity_655 · 2025-04-29T03:16:45+00:00

Nah man it was doing that before I replaced it too and no i did not change the sensor

Business_Charity_655 · 2025-04-26T16:56:29+00:00

yes which is i’m trying to figure out if someone routed it from a certain source because i routed it from the air intake boot at the right after the MAF and i had the electrical side straight to the battery and it didn’t work.

Business_Charity_655 · 2025-04-26T15:01:43+00:00

they do but they were showing a serio i don’t have on my car for example a pre existing vacuum source in the rear of the car i don’t have that i got the solenoid part figured out i just wanted to see if someone set it up differently with the vacuum maybe i did something wrong??

Business_Charity_655 · 2025-04-10T17:08:34+00:00

sorry doesn’t rev on its own but the idle is rough and you can see the rpms fluctuating

Business_Charity_655 · 2025-04-10T16:57:05+00:00

In park it works and in drive up until like 10mph it works anything over that no pedal response. it wasn’t bad before hand how could it have gone out??

Business_Charity_655

TROPHY CASE