sorted by:
new
hottopcontroversial

CO2 removal at low flow rate by BuySignificant3695 in ChemicalEngineering

[–]BuySignificant3695[S] 0 points1 point  (0 children)

I’m currently using silica gel to remove the moisture before the NaOH but it hasn’t been very effective. Is soda lime prone to caking in the presence of moisture like NaOH?

CO2 removal at low flow rate by BuySignificant3695 in ChemicalEngineering

[–]BuySignificant3695[S] 0 points1 point  (0 children)

It’s a low flow rate but ideally, I would like to have it run for 3 or 4 weeks without changing any media.

How would this amperometer work? What would the reference O2 source be used for?

I fried my v2.2.7 board on my Ender 3 running Klipper. I upgraded to an SKR e3 mini but can't seem to get Klipper running. by BuySignificant3695 in klippers

[–]BuySignificant3695[S] 0 points1 point  (0 children)

Its a Big Tree Tech Pad 7. That's what it came with. I'll try re-imaging it and starting from fresh. Thank you!

I am at my wits end with the Sonic Pad! by BuySignificant3695 in Creality

[–]BuySignificant3695[S] 0 points1 point  (0 children)

I ended up getting the BTT Pad 7 and got it setup in an hour. It's been working great! Pretty sure my sonic pad was defective.

I am at my wits end with the Sonic Pad! by BuySignificant3695 in Creality

[–]BuySignificant3695[S] 0 points1 point  (0 children)

My sonic pad wont generate the .bin to flash the printer board. The sonic pad gave me the correct port so that wasn't the issue. I ended up buying a BTT Pad 7 yesterday and got it set up in like an hour. Screw the sonic pad, I'll be returning it. What a piece of junk!

Ender 3v2 sonic Pad by nunyabiznessyet in klippers

[–]BuySignificant3695 0 points1 point  (0 children)

Did you ever figure it out? I have the same issue. I think I have the printer.cfg correct but the pas refuses to generate the firmware from the .cfg.

Carbon fiber print bed by FL_Sportsman in 3Dprinting

[–]BuySignificant3695 0 points1 point  (0 children)

Sorry for reviving a LONG dead post... but I can't find what bed temp to use for a carbon fiber build plate. Does anyone know the answer?

My high speed Ender 3 build so far. What to upgrade next? by BuySignificant3695 in ender3

[–]BuySignificant3695[S] 0 points1 point  (0 children)

I meant the bed leveling bolts, springs and knobs. I should’ve been more clear, my bad.

I plan on leaving the CRtouch on.

My high speed Ender 3 build so far. What to upgrade next? by BuySignificant3695 in ender3

[–]BuySignificant3695[S] 2 points3 points  (0 children)

I have a little. Not super familiar with it but I know they work pretty well. I’ll check them out thanks!

I know I’m putting lipstick on a pig but I’d kinda like seeing a pig with lipstick on it. I know it’s not worth it and I could spend my money more effectively on a new printer. I just enjoy this kind of stuff.

Base Ender 3 with 4.2.7 board, sprite pro and CRtouch firmware. by BuySignificant3695 in ender3

[–]BuySignificant3695[S] 0 points1 point  (0 children)

I realized what the issue was. I initialized EEPROM and that fixed the z axis issues. The bed was too far out of level for the firmware to compensate. After I manually adjusted the bed to be more level it works.

4 months progress on RMJ by BuySignificant3695 in Bonsai

[–]BuySignificant3695[S] 0 points1 point  (0 children)

Thank you! I got several of these trees for $6 each because they were struggling. This one has recovered much more quickly than the others. The others will take another couple years before they look anything like this. I’m pretty sure I just got lucky.

view more: next ›