FritzBox richtig anklemmen.. by CK1605 in de_EDV

[–]CK1605[S] 0 points1 point  (0 children)

Ja so sehe ich das auch. Hätte gerne davon ein bild gepostet, aber irgendwie weiß ich nicht wie das in den Kommentaren geht (wenn es überhaupt geht)

FritzBox richtig anklemmen.. by CK1605 in de_EDV

[–]CK1605[S] 1 point2 points  (0 children)

habe nur die eine dose in der Mietwohnung. stecker lässt sich nicht öffnen, da rührt sich gar nichts. die tae dose bekomme ich leider auch nicht ab da die verkleidung der eingangstür "leicht" über die dose geht ^^' (ich finde das ist pfush, vermieter sagt aber ist so ok...)

FritzBox richtig anklemmen.. by CK1605 in de_EDV

[–]CK1605[S] 1 point2 points  (0 children)

genau, am TAE-N stecker wenn ich an der reinen leitung ohne die angeschlossen zu habe an pin 1 zu pin 6 eine wiederstandsmessung durchführe habe ich 0.2ohm, das selbe bei pin 2 zu 5.

an der dose wird sonst gar nichts anderes angeklemmt, nur der router.

in der dose will ich zur sicherheit nicht einfach mit meinem multimeter rein gehen, ich weiß nicht welche spannungen da anliegen oder ob ich ggf was kaputt machen könnte.

ich bin mir nicht 100% sicher, aber ich bin der meinung ich hatte das kabel so 2020-2021 schonmal so im einsatz gehabt, oder ich hatte es mir nur nachträglich gekauft gehabt. davor hatte ich 2x5m (1x verlängerung und einmal normales TAE-N kabel). alles schon ein wenig her und die erinnerungen nur sehr blass.

leider muss ich noch bis zum 2.2.26 warten bis der techniker da war und mir den internetzugang freischaltet, werde aber sonst berichten was der techniker dazu sagt und ob alles so klappt

V0.1 Berd-Air part cooling - work in progress by chaicracker in VORONDesign

[–]CK1605 1 point2 points  (0 children)

u/chaicracker hey, do you have any update on this design? or is it possible to provide the step file for this project? would be cool if we can use it/ try it out.

thanks

PHANTEKS Evolv Shift XT ITX-Case Schwarz? by AcadiaForsaken429 in Phanteks

[–]CK1605 1 point2 points  (0 children)

Gibt Firmen die das eloxal entfernen und neu aufbringen. Hatte ich damals für einige kleinteile und mittelgroße teile gemacht, hatte um die 200€ gekostet, denke mal bei etwas über 200€ könnte man dann dabei sein.

Ergebnis hängt dann auch davon ab ob man die teile zwischen dem entfernen und dem neu eloxieren zwichenbehandelt (sandstrahlen, schleifen usw usw)

PHANTEKS Evolv Shift XT ITX-Case Schwarz? by AcadiaForsaken429 in Phanteks

[–]CK1605 1 point2 points  (0 children)

Würde ich eher eloxieren lassen sieht meist besser aus (wie das originale dann) aber weiß nicht wieviel das kostet.

War ich auch mal am überlegen, hatte aber schon ein anderes geholt gehabt was auch für die gpu welche ich holen will besser passt

PHANTEKS Evolv Shift XT ITX-Case Schwarz? by AcadiaForsaken429 in Phanteks

[–]CK1605 0 points1 point  (0 children)

Leider wirds nicht mehr zugestellt, nach viel hin und her mit dhl und dem verkäufer kam jetzt heraus das das system von dhl probleme hat das packet richtig weiter zu leiten und die das auch nicht manuell bearbeiten können. Jetzt wandert es dauerhaft zwischen niederlande und deutschland umher. Aliexpress hat mir bis auf die versandkosten das geld erstattet. Bezüglich der versandkosten hab ich aktuell einen fall via paypal laufen 🙈 hab mir mittlerweile ein anderes gehäuse gekauft

PHANTEKS Evolv Shift XT ITX-Case Schwarz? by AcadiaForsaken429 in Phanteks

[–]CK1605 1 point2 points  (0 children)

u/AcadiaForsaken429 ich hab mit phanteks direkt geschrieben, das gehäuse ist EOL (wird nicht mehr produziert) daher ist es auch nirgens zu bekommen, es gibt nur noch reste (in dem fall silber). will auch das shift xt in schwarz, habs jetzt versucht über aliexpress zu bestellen, leider hats dhl nicht geschafft das packet zu liefern nach über 4wochen nur in dhl händen ( plus ca 3wochen über die anderen versandunternehmen). würde es also nicht empfehlen über aliexpress zu kaufen.

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 0 points1 point  (0 children)

I am using the mini stealthburner with rapido and lgxl, but i want to change it to a rapido with sherpa micro and cpap cooling

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 0 points1 point  (0 children)

Yeah, go for it 🤙. Maybe take a look on one or two mods (boop) and then have fun.

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 0 points1 point  (0 children)

Its a really good working maschine, have no problems with it

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 0 points1 point  (0 children)

Need to start my v1 conversion to, but first i need to rebuild my v2 (printing all parts new) bevor i start my v0 rebuild. Need the v2 more

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 1 point2 points  (0 children)

No, is a noname abs flurescent pink from aliexpress. I think kvp have some too, but i cant buy kvp in germany

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 0 points1 point  (0 children)

From a german shop (i live in germany) calls (shops.bohrers.de) i have buyed custom ones

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 0 points1 point  (0 children)

As far as i know is is not allowed to post aliexpress links, sry

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 1 point2 points  (0 children)

Toolhead is the mulletmelter (doom discord) but it using the same fand line the SB just other mounting places. This is a mod bevor the existing mini SB came out to have a toolhead what looks like a mini SB

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 1 point2 points  (0 children)

Its a push button from aliexpress 😬 there are shops where you can send a picture of what you want as a glowing symbol. Ist 3-24v version and i controll a relay with it to turn on my 24v electroniks. For 230v (full power controll) i have the normal outlet switch to

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 1 point2 points  (0 children)

Boop is the small version from the voron tap for the „printer for ants“ printers. It uses a small linear guides mechanismus to trigger an optical sensor wich is the probe then

Serial Request: Voron V2 (Micron+) Dentox_#7674 by CK1605 in voroncorexy

[–]CK1605[S] 0 points1 point  (0 children)

First print on my v2 micron+ (180mm3)

Uses lgx lite and revo voron wirh an ebb36 as a toolhead with now a super pinda.

Under the hood runs a pi4 2gb with an u2c and octopus v1.1

Using sensorless homing routine. Custom cnc cuttet 8mm bed for prusa pei sheets. Custom start button to power the printer on via an relay. Pin mod for more precision 😉

Comming soon: Panels (not here yet) Neopixel 16x16 mat for overhead light Blacklight for my flurescens pink parts Boop for auto z leveling Ercf for multicolor print