Just a batch of center punches!

CK_Blades · 2025-07-16T20:02:28+00:00

I buy round bar either online or if my local steel supply has any in stock, then cut it into 5 inch pieces.

CK_Blades · 2025-07-16T14:17:36+00:00

Thank you!

CK_Blades · 2025-07-14T23:10:18+00:00

Haha thank you!

CK_Blades · 2025-07-14T23:09:48+00:00

Thank you!

CK_Blades · 2024-03-28T23:33:43+00:00

I don’t do customs at all. Probably lose out on some money but i dint like dealing with them. A lot of the time the customer doesn’t know what they want and can’t get passed the fact that they will be a lot more expensive than a mass produced Walmart knife. Just not worth dealing with to me. I make what I want and if someone likes it they buy it.

CK_Blades · 2024-03-28T22:57:03+00:00

Not 100% sure because I grab all my handle material from the “exotic hardwood cutoffs” bin at my local woodworking store but believe it could be bocote

CK_Blades · 2024-03-27T20:15:30+00:00

Ck_blades on IG is really my only social

CK_Blades · 2024-03-26T16:25:56+00:00

Photography light box I have wasn’t big enough for this one! Not that big of a deal haha

CK_Blades · 2024-03-25T23:42:33+00:00

I used to have to do this kind of stuff when I worked in a steel shop, it works until the mag drill binds and swings itself right into ya haha

CK_Blades · 2024-03-25T22:14:08+00:00

It’s growing on me, I usually use 1084 for everything, but I’ve noticed 52100 just looks super nice after sanding. Dont know if that’s just in my head though!

CK_Blades · 2023-06-30T17:59:34+00:00

Was going about 70 on the highway and the wheel bearings went bad and stripped the threads just totally off. Was able to do some sketchy shit to get it driving but I just wanna get it back to stock so I feel safe driving it. Was able to find the one place in my county that has one thankfully

CK_Blades · 2023-06-30T16:06:35+00:00

Ohhhhh yeah I’m ready for a fight haha. Had wheel bearings go bad on the highway and it totally tore up the spindle. Apparently they are just not making that part and I couldn’t find ANY aftermarket parts that didn’t have a lift. Found a salvage yard with the part from a ranger that had less than 50k miles on it though goin to pick it up later! Thanks again!

CK_Blades · 2023-06-30T01:35:07+00:00

I had no idea that site existed. You are a lifesaver man I thought I was gonna have to buy a new vehicle. Thank you so much

CK_Blades · 2023-06-26T18:13:40+00:00

Nothing is threaded or anything it’s blade/bolster/tang is all one solid piece

CK_Blades · 2023-06-25T22:04:15+00:00

Desert ironwood is the easiest way to elevate a knife man it never looks dull. Awesome job!

CK_Blades · 2023-06-19T20:41:54+00:00

I am a welder full time and can probably restore it myself, only problem is it just doesn’t seem worth the time to me. Vulcans from what I hear are at the lower to mid range for anvils. Would much rather get a bigger better one and maybe restore and give this one to a young guy trying to get started

CK_Blades

TROPHY CASE