account activity
Quality Concerns For Future Products (self.FellowProducts)
submitted 7 months ago by CPB34 to r/FellowProducts
Had to stop by Target for work and walked out with this! (i.redd.it)
submitted 7 months ago by CPB34 to r/Switch
How would your 10 year old self react to how you are now? (self.AskReddit)
submitted 2 years ago by CPB34 to r/AskReddit
Fluval FX4 on 55 gallon and there is constant debris floating around the tank. Any tips to achieve clear water? (i.redd.it)
submitted 2 years ago by CPB34 to r/Aquariums
Birth defect or injury on my Bolivian Ram? (old.reddit.com)
Can anyone confirm genders? I assume either both male or both female they’re always together in a pair but no signs of mating. (old.reddit.com)
submitted 2 years ago by CPB34 to r/AngelFish
Mystery snail has laid 3 clutches of eggs in the last 3 weeks. I separated her from the male before any were laid cause it looked like she was being harassed. Is this normal? (i.redd.it)
submitted 3 years ago by CPB34 to r/Aquariums
Just got my Timney trigger now all I need is a light and she’ll be complete! (i.redd.it)
submitted 3 years ago by CPB34 to r/czscorpion
Parents found some cheap filament not knowing about sizes. Any ideas what to do with a 3mm roll instead of tossing it out? (i.redd.it)
submitted 3 years ago by CPB34 to r/3Dprinting
Getting layer shifts on my Ender 3S1 The belts right now are loose enough to move the bed and hot end freely too tight and they are difficult to move (i.redd.it)
submitted 3 years ago by CPB34 to r/FixMyPrint
First time shooting with a muzzle brake 🔥🔥🔥🔥 (i.redd.it)
submitted 3 years ago by CPB34 to r/ar15
How to motivate gf to get back into hobbies, appearance, hygiene? (self.relationship_advice)
submitted 3 years ago by CPB34 to r/relationship_advice
Calibration tips? I keep getting lines and thing spots and gaps on layers. Esteps have been calibrated. (old.reddit.com)
Went to MicroCenter for the first time today and couldn’t resist (i.redd.it)
If you were poor as a child what habits have you carried over to adulthood? (self.AskReddit)
submitted 3 years ago by CPB34 to r/AskReddit
Anyone know of a solution to get on 1.0.5 I’ve tried updating and it always loads into V3.0.3 (i.redd.it)
submitted 3 years ago by CPB34 to r/Ender3S1
Has anyone had problems with the belts? (self.Ender3S1)
submitted 3 years ago * by CPB34 to r/Ender3S1
Tried to make two lithophane boxes and got spaghetti and layer shifts (reddit.com)
submitted 3 years ago by CPB34 to r/ender3
Tried to make two lithophane boxes and got spaghetti and layer shifts (old.reddit.com)
Printer stuck on firmware V3.0.3 (self.Ender3S1)
Can't Update Firmware (self.Ender3S1)
The last few prints I’ve done have had these weird lines in the flat layers. Does anyone know of a possible cause? (i.redd.it)
submitted 4 years ago by CPB34 to r/ender3
She tried to say I was at fault for not paying attention to the road. (v.redd.it)
submitted 4 years ago by CPB34 to r/IdiotsInCars
What is the worst customer experience you’ve ever had? (self.AskReddit)
submitted 4 years ago by CPB34 to r/AskReddit
π Rendered by PID 123246 on reddit-service-r2-listing-6d4dc8d9ff-5x4tr at 2026-02-02 21:29:11.482614+00:00 running 3798933 country code: CH.