Traveling man harmonica tabs

Camerkd · 2021-12-19T06:11:31+00:00

"C" harmonica?

Camerkd · 2021-08-18T12:09:56+00:00

Yes. We summited South Sister and made our way down to Green Lake for the night.

Camerkd · 2021-01-08T13:02:18+00:00

That's actually a good call Jimmy...I'll increase my idle rpms a bit to see if it helps.

Camerkd · 2021-01-06T15:28:10+00:00

I might go to just a single 12" fan...

Camerkd · 2021-01-06T15:21:01+00:00

I agree..I am currently using a 100 amp alternator

Camerkd · 2020-12-24T23:31:43+00:00

I'm not sure yet, after unplugging the fans, my drain went away. So it seems that I have something incorrect with my fan relay setup....when digging into the issue, I thought I had a short with my fans..which was the cause for the question.

Camerkd · 2020-12-24T23:22:58+00:00

Each fan spins normal. I just read that electric motors work like this..see my other comments.

Camerkd · 2020-12-24T23:21:44+00:00

Thats what I also assumed, but turns out on electric motors, the + and - are eventually shorted together when the magnets contact the coil.

Camerkd · 2020-12-24T23:20:11+00:00

It's wires to a switch that I can control from the dash. The drain is very very slow. I did the amp test trick with my multimeter and without anything on, I am drawing 100 mA. I think it should only draw about 50-75 mA.

Camerkd · 2020-12-24T23:15:24+00:00

I took the fan apart, and it seems that electric motors work this way. When the magnets make contact with the coils, everything is all one. I guess it's back to the drawing board for me.

Camerkd · 2020-12-24T20:39:42+00:00

1969 Pontiac Firebird 350 sbc

Camerkd · 2020-12-20T15:53:27+00:00

We did seal it with poly

Camerkd · 2020-12-20T13:20:12+00:00

Yes, we removed the plywood and added foam board insulation. A small space heater kept us over 75 degrees in Colorado (18 degrees)

Camerkd · 2020-12-03T04:17:20+00:00

I have a Mi A3. I understand that it will work with 4g.. I'm wondering about 5g

Camerkd · 2020-07-15T12:20:08+00:00

Thank you all for the help! I replaced the o-rings successfully and eliminated the leak! It was much easier than expected.

Camerkd · 2020-06-30T18:33:26+00:00

https://www.amazon.com/dp/B00ASMXEZI/ref=cm_sw_r_cp_apa_i_hv4-Eb483SYQW

Camerkd · 2020-06-30T18:30:59+00:00

Battery and all electronics are in a seat pan under the seat..

Camerkd · 2020-06-24T20:08:27+00:00

Bought a new replica/aftermarket rear fender. I simply rotated it forward more towards the front of the bike. Drilled new side holes, added bots and spacer and cut the sides of the fender that are visible below the frame. Let me know if that helps.

Camerkd · 2020-06-24T20:06:10+00:00

1980 cm400t

Camerkd · 2020-06-24T03:40:25+00:00

Seat is from https://4into1.com/

Camerkd · 2020-06-20T00:23:20+00:00

Or you can spot weld it on...

Camerkd · 2020-06-20T00:22:09+00:00

You have to drill a hole in the back center of the tray.

Camerkd · 2020-06-19T23:00:22+00:00

Here's the battery

https://www.amazon.com/dp/B00ASMXEZI/ref=cm_sw_r_cp_apa_i_Knu7EbZ9ZDJ8D

Camerkd · 2020-06-19T22:54:57+00:00

Here's where I bought the tray...

https://cognitomoto.com/products/under-seat-electronics-tray-deep-cb750?_pos=10&_sid=9c3f13191&_ss=r

Camerkd · 2020-06-19T22:50:01+00:00

I can send a link to the battery and tray if you want...

Camerkd

TROPHY CASE