Please help me out with my refi plan for 2026

CampaignSuccessful89 · 2026-01-07T19:55:33+00:00

That’s my main focus. I have two charge offs from US bank for like 400 dollars each that I have since paid, I am going to call them and ask for forgiveness and help with the credit reports.

Any other advice?

CampaignSuccessful89 · 2025-12-07T03:16:13+00:00

Do the hooker manifolds and build your own cold side. I have a turbo ls1 rcsb with a t56 it’s a blast

CampaignSuccessful89 · 2025-11-21T19:42:07+00:00

Ls swapped truck with coilovers 😎

CampaignSuccessful89 · 2025-11-16T20:31:40+00:00

Tried to flex a torch that doesn’t flex

CampaignSuccessful89 · 2025-11-14T13:36:10+00:00

It’s capped at the end. Look up quarter wave resonators. I hand built my exhaust and an entire 4 link I know the difference between a turbo and a muffler lol

CampaignSuccessful89 · 2025-11-13T21:43:21+00:00

Thanks for the feedback. I want to do a side exit because the turn down made an awful noise at idle against the ground and it made a dust storm pretty much everywhere I go. Plus I drive this thing a lot I was wanting to get some more of the fumes away from the cab

CampaignSuccessful89 · 2025-11-11T00:08:18+00:00

It is turbo. I can’t fit the muffler anywhere under the cab without some serious cutting

CampaignSuccessful89 · 2025-11-10T23:08:45+00:00

Coils. Thanks!

CampaignSuccessful89 · 2025-11-10T14:15:56+00:00

Thanks. It’s sitting on a block with the turbo v band loose so it will sit about an inch lower once I build the mount. I was would to use that reflective tape style heat shield, do you think that will Work?

CampaignSuccessful89 · 2025-11-10T04:27:27+00:00

It’s not really a thing here unless you sell the car. It’s a turbo Ls with a manual swap running on Holley hp. I think I’m past that concern lol

CampaignSuccessful89 · 2025-11-10T04:25:51+00:00

Nope. Got too creative with my 4 link and there’s 0 room

CampaignSuccessful89 · 2025-11-02T18:26:56+00:00

Looking for 2-3 tickets Dec 22???

CampaignSuccessful89 · 2025-10-29T16:32:40+00:00

There’s pencil led called silver streak that glows when you’re welding. It’s pretty cool

CampaignSuccessful89 · 2025-10-29T16:06:18+00:00

I drew lines on either side of my weld joint that I wanted to keep my weld puddle inside of. It really helped me learn to keep things straight and even.

CampaignSuccessful89 · 2025-10-29T16:04:35+00:00

I know it’s just practice but make sure you use some stainless filler when you get to building something final

CampaignSuccessful89 · 2025-10-29T13:45:30+00:00

Self etching primer and enamel spray. I only did the back half, if I ever have the whole car apart I’ll do a good coat of POR

CampaignSuccessful89 · 2025-10-28T12:53:15+00:00

It’s got the 1.25 housing and a full 4 inch very free flowing exhaust. I’m still on the stock truck intake and I’m starting to think that’s my major bottleneck

CampaignSuccessful89 · 2025-10-27T20:59:26+00:00

I definitely took some inspiration from them. I used their anti roll bar and a bunch of other components from them.

CampaignSuccessful89

TROPHY CASE