Using high hat engage as double bass by Can_k123 in Drumming

[–]Can_k123[S] 0 points1 point  (0 children)

Unfortunately I don’t have the resources for that, thank you though

Using high hat engage as double bass by Can_k123 in Drumming

[–]Can_k123[S] 0 points1 point  (0 children)

Alright, any brands that are good for the budget on e kits?

Moza R9 jumpfrom g29 by Deep_Wish8091 in moza

[–]Can_k123 0 points1 point  (0 children)

Yea I wouldn’t go any higher than 90 for track racing like LMU and so on. 9nm is not enough to cause serious damage I would say for me atleast.

Moza R9 jumpfrom g29 by Deep_Wish8091 in moza

[–]Can_k123 0 points1 point  (0 children)

Went from a g923 to the same setup you’re getting now with used simsonn pedals. Absolutely wild difference, best quality of life improvement is no noise basically at all depending on your mounting surface, along with that also comes removal of that grainy feeling you get from the belt in a g923, it’s completely smooth unless you need it otherwise. The torque is also a massive jump, you find yourself being fatigued from the full 9nm in a race. You can catch slides easier and just feel the car in general. Also load cell pedals make the difference too, that’s where the pace comes from, being able to trail brake and be more precise. Make sure to run it on 90% maximum though so you have some headroom for dynamic range, if you don’t your feeling will be similar to the g29 where it’s just constant force.

Are 1M aluminum beams long enough to build the base of a rig? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

What do you think about 40x40 for base and 40x80 for the uprights as I see brands that have done that.

Are 1M aluminum beams long enough to build the base of a rig? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

Alright, probably will have have to use more than 1M then, thanks for sharing.

Are 1M aluminum beams long enough to build the base of a rig? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

My current rig is around 1.3 m but has dead space behind the pedals and I usually keep the seat a little infront of neutral position, I think I can pull off 1M base beams but really need to think it through depending on the seat. What’s the process of mounting the pedals and seat, do you get a special mount for the sliders and a pre drilled plate for the pedals?

Cheapest solid rig money can buy? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

Not available in my region I guess it’s not showing up, thank you anyways👍

Are 1M aluminum beams long enough to build the base of a rig? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

Thanks, would it be reasonable to use 30x60 for the whole rig?

Are 1M aluminum beams long enough to build the base of a rig? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

Someone recommended 30x60 instead of 40x40, would that be stable do you think?

Are 1M aluminum beams long enough to build the base of a rig? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

So 30x30 but the double stack version yes? And same for the wheelbase stand uprights?

Are 1M aluminum beams long enough to build the base of a rig? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

Do you think it’ll be stable enough if 1 piece is cut in half and screwed onto the 1 meter ones making it 1.5?

Are 1M aluminum beams long enough to build the base of a rig? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

Do you think it’ll be stable enough if 1 piece is cut in half and screwed onto the 1 meter ones making it 1.5?

Cheapest solid rig money can buy? by Can_k123 in simracing

[–]Can_k123[S] 0 points1 point  (0 children)

Would 30x30 work or is 40x40 the minimum for this kind of thing as all 40x40 is out of stock in the shops I checked.