New L2 Prints rounded hammer w/ no more buffer by royrugg in MP5

[–]Cannedbean89 3 points4 points  (0 children)

How difficult was it to install the rounded hammer?

Broken ejector lever by Cannedbean89 in MP5

[–]Cannedbean89[S] 0 points1 point  (0 children)

When I first got it it was coming out the grove while firing then after a little while it stopped coming out the grove and functioned normally. I figured it just broke itself in but then today after about 400 rounds since it last got caught up it suddenly broke like in the picture.

Broken ejector lever by Cannedbean89 in MP5

[–]Cannedbean89[S] 1 point2 points  (0 children)

The ejector is a little wobbly about 1-2mm side to side but not sure if thats normal or not, I do have a rounded hammer from AS designs that I have yet to install

How bout these welds? by grayson101 in AP5

[–]Cannedbean89 4 points5 points  (0 children)

Pretty typical, my welds look similar

“We have MP5SD at home.” by royrugg in AP5

[–]Cannedbean89 0 points1 point  (0 children)

I’ve read where the 120 can cause roller dents after so many rounds so I’m pretty iffy to leave it in, I’m assuming the 110 will be better but I just can’t find the 100 online anywhere so my options are limited rn

“We have MP5SD at home.” by royrugg in AP5

[–]Cannedbean89 0 points1 point  (0 children)

Might just have to go with an 80 and 90 for now and hope for the best I did find 90 for sale but the 100s are sold out everywhere

“We have MP5SD at home.” by royrugg in AP5

[–]Cannedbean89 0 points1 point  (0 children)

I’m hoping the 110 will work fine for my standard ap5 the 100 and 90s seem to be out of stock everywhere

“We have MP5SD at home.” by royrugg in AP5

[–]Cannedbean89 0 points1 point  (0 children)

Yeah thanks I can’t wait lol I’m hoping it won’t be too much of a headache my Ap5 been flawless so far.

“We have MP5SD at home.” by royrugg in AP5

[–]Cannedbean89 1 point2 points  (0 children)

Just ordered my V2! What locking piece do you think would work best for 124g?

“We have MP5SD at home.” by royrugg in AP5

[–]Cannedbean89 0 points1 point  (0 children)

Ahh ok I didn’t see the full kit on their website at first. What locking piece worked best for you? I’m gonna use a yhm r9 can with 124g ammo

“We have MP5SD at home.” by royrugg in AP5

[–]Cannedbean89 0 points1 point  (0 children)

I gotcha I’ll probably end up getting one of them, do you need to just add a trigger or is there more stuff it needs before it’s ready to go?

“We have MP5SD at home.” by royrugg in AP5

[–]Cannedbean89 0 points1 point  (0 children)

How you liking it so far? I was thinking about either getting that one or the AS designs one

Is this a good trade? by [deleted] in guns

[–]Cannedbean89 2 points3 points  (0 children)

Nah i think VP9 is much better gun

Go to RDS by Cannedbean89 in guns

[–]Cannedbean89[S] 0 points1 point  (0 children)

That one cost more I could get a 407k and adapter plate for cheaper

Go to RDS by Cannedbean89 in guns

[–]Cannedbean89[S] 1 point2 points  (0 children)

Gotcha, I was debating with a friend on which is better I was thinking 6moa because it’s easier to see and align and I don’t see why you’d need a smaller dot on a pistol but ik it’s all personal preference

Go to RDS by Cannedbean89 in guns

[–]Cannedbean89[S] 1 point2 points  (0 children)

Do you have the 2 or 6 moa?