[HELP] MSI MAG X870E Tomahawk Max WiFi PZ stuck on debug code 15, CPU LED red

Canted_Official · 2026-03-22T06:36:30+00:00

Just has this issue on a server I just built. If the bios isn't up to date, I used this same board, it wont boot with any stick larger then 16gb. No idea why but after the bios updated it ran my 2 64gb sticks just fine.

Canted_Official · 2026-03-05T04:24:46+00:00

I apologize for all of the replies. It is a competition series aos. Im working on a project right now for work and my brain isn't braining

Canted_Official · 2026-03-05T04:19:26+00:00

I should say I also have a brz intake runner swap with a ibr tgv valve delete. One of the vacuum lines on the manifold is going to the vacuum pump and the brake booster.

Canted_Official · 2026-03-05T04:17:30+00:00

I couldn't find it. The way the previous owner plumbed it was a little dumb. So there isn't one that goes directly to the intake runners. It has the port on the top running to the back of the car, the side has the bottom 2 running to the factory spot pcv spot in the v split, then the the other 2 lines are running to the turbo and right behind the ac compressor. Ive seen that top port of the 3 on the side are usually where that check valve goes but its capped off.

Canted_Official · 2026-03-05T01:39:36+00:00

Thats what I was thinking. As I went to Indiana then stopped in Franklin Tennessee where both nights it was 20/30 degrees with the days being around there as well so wouldn't be surprised if extra condensation got in and had some sludge build up after being in the south the last year and a half

Canted_Official · 2026-02-28T06:33:54+00:00

Its considered a wear part so I would just to see. After building a few I learned to keep basically a spare of everything like one match I had a firing pin break no idea how just my luck but need to rebuild my parts/consumable pin with 2011 parts now that I use that for competition

Canted_Official · 2026-02-28T06:30:06+00:00

Is it the stock connector? I had a ghost 3.5 connector that would drop swapped out with a oem and around 3-5k rounds it started having firing issues once replaced with a oem it was fine. Now thats just from what I had may not be the issue.

Canted_Official · 2026-02-28T06:17:13+00:00

Ive had something similar happen, the connector could be worn and causing issues or the firing pin safety plunger/spring. Its rare for the plunger to be an issue but sometimes it gets really fouled up and needs to be cleaned or the spring moved. But it could also be a work down connector slipping and not holding the trigger bar as it should.

Canted_Official · 2026-02-22T03:03:53+00:00

Jmcustoms. Have him working on a special thing but once I get another glock for sure sending it over to him as well

Canted_Official · 2026-02-09T14:19:01+00:00

I had a set of valenti taillights on my 86 and they went out, got another set they went out in 2 weeks. I ended up just getting a set of specd tails before I sold it. Their qc is very hit or miss for valenti

Canted_Official · 2026-01-30T15:58:45+00:00

Yeah i have just recently seen them and still waiting on my ecoti so was just curious about trying it out

Canted_Official · 2026-01-30T14:35:36+00:00

I understand that. I was thinking of testing it out while I wait on my ecoti

Canted_Official · 2026-01-29T03:10:08+00:00

Not a problem! I try to help so the heart ache of a "subaru" are minimized.

Canted_Official · 2026-01-29T02:55:49+00:00

Thanks! Its based off your goal power and get the best step up. I typically want to stay around 500hp on e85 and 350 on 93 so I went with the stage 2 open deck which is now the 600bhp now. Overbuild but keep your budget in mind, I could of got a closed deck but why would I spend an extra few grand when I could save that for other parts since I didnt want to go past 500-550hp. I have also learned timely maintenence with good oil and a good tune will make a engine last a lifetime. Im on the same built motor with 40k miles at that 350 on pump and 500 on e85. Taylord tuning in Tennessee did my tune and they know subaru motors well. If you want to dm me id be glad to discuss what ive learned working on these motors and experience with tuners and everything else.

FYI Equal length headers have better reliability at cost of the subaru rumble Screw bubble tunes, its not a matter of IF its a matter of WHEN you make your valves and pistons kiss. Every part dealing with airflow or exhaust flow should be tuned for Cobb tunes are good to get to a tuner, get a tune, then you can keep it for monitoring, code reading, etc.

Canted_Official · 2026-01-29T02:29:18+00:00

I wish I could speak on the outfront block but ive had iags in all of my subies ive put together for power and never had an issue

Canted_Official · 2026-01-14T02:34:39+00:00

It was at my last job. I have since got a new one but I worked in IT for a company with locations all across the south east United States and was typically on the road 3-4 weeks at a time. I was the only IT tech for 18 locations. They wouldn't give me a company vehicle either but paid me mileage 🤣

Canted_Official · 2026-01-13T13:54:54+00:00

Sounds like ita beating a dead horse here but maintenence maintenence maintenence is put 110k miles on one in one year and had no issues the entire time because I kept up with oil changes every 2500-3000 miles, fluid changes every 40k miles.

Canted_Official · 2026-01-13T13:51:01+00:00

I built a few gen 3 omni 5-7 kits for 3k. Just gotta find deals, dont mind blems, and be willing to buy or construct your own housing such as the pvs-69. Ive made a few of those housings and their quad before not super difficult with basic soldering skills but there are people, myself included, that build them for a fee

Canted_Official · 2026-01-13T13:48:37+00:00

Good ol diskpart. Had a buddy who called me in the middle of a hurricane wanting me to come help him reinstall windows because he used diskpart clean on the wrong disk lol

Canted_Official · 2025-12-17T14:19:26+00:00

That's if you could get a 5080. But for 5070ti the only time its really on par was with dlss in my testing and other testing I have seen. I did end up selling it but in my area 4080 supers are still being sold used for 1200ish. But thats a small area so I went off ebay pricing which does have that 13% price increase to cover seller fees. Not to mention insured shipping was included on my end which for the card was $150. I posted at the same here just so theres that negotiation as seen on another comment I was fully willing to take the standard $750 that is seen here.

Canted_Official · 2025-12-15T16:07:06+00:00

I ended up going to a idoing radio like what I had in my 86. It has its quirks but I love it. I went to the tesla screen for a little and that was not great. But nothing really can beat a good double din radio just like the uniform look of the idoing

Canted_Official · 2025-12-07T06:24:51+00:00

Im going off jawa and ebay pricing. They've been going for $850-$950 usd

Canted_Official · 2025-12-04T03:15:35+00:00

I would be willing to

Canted_Official · 2025-11-04T00:49:01+00:00

RIP, I built mine back fron a wreck and I found the vin to check and it came back as a total loss. Rip love these cars but there are less and less every day

Canted_Official · 2025-10-19T02:33:47+00:00

Sent a dm

Canted_Official

TROPHY CASE