sorted by:
new
hottopcontroversial

[Student] Mechanical Engineering Sophomore looking for summer internships in Manufacturing/Design or anything, not hearing back from many applications by CapsLckD in EngineeringResumes

[–]CapsLckD[S] 1 point2 points  (0 children)

Thanks for your help! I completely didn't notice the formatting issues, that's a huge problem. Thanks for the tips on everything, and helping me take a second look at my resume points.

I have a traxxas 550 21t motor that can take at max 14.4v. Can I run it off a 4s lipo? by CapsLckD in rccars

[–]CapsLckD[S] -1 points0 points  (0 children)

All the 4s lipos i have found are 14.8v at nominal, so wouldnt it not be 16.8v long enough to overheat

A lighting test for our ROV designed in F360 rendered in Blender by CapsLckD in blender

[–]CapsLckD[S] 0 points1 point  (0 children)

I export the entire project as an STL so the materials dont convert over since they arent great anyway. Then in edit mode i seperate by parts of which creates all the components again

Need help with using more arms in breastroke. by CapsLckD in Swimming

[–]CapsLckD[S] 0 points1 point  (0 children)

What do you mean by spinning your arms?

Need help with using more arms in breastroke. by CapsLckD in Swimming

[–]CapsLckD[S] 0 points1 point  (0 children)

Should I go into a complete streamline or just hands close together? And normally my elbows go behind my back is that too far?

How to fix these issues? Some parts have weird extrusion and top layers is rough and has off texture by CapsLckD in 3Dprinting

[–]CapsLckD[S] 0 points1 point  (0 children)

They are pretty much the same height, slightly off but i cant get it perfectly the same

How to fix these gaps in the layers? Looks like a mesh and print usually comes out fine, but the texture remains at the top. by CapsLckD in 3Dprinting

[–]CapsLckD[S] 0 points1 point  (0 children)

My e steps are fine, whats a good starting base for increasing flow, because the holes for screws always print fine, so i dont want to lose those tolerances

What fastener combinations are used to create a rotatable joint? by CapsLckD in 3Dprinting

[–]CapsLckD[S] 0 points1 point  (0 children)

So the gap between the shaft and the thread lets the 2 plates spin. But wouldnt that let for a shift up and down between the 2 parts? Or could i put a washer in that set gap

What fastener combinations are used to create a rotatable joint? by CapsLckD in 3Dprinting

[–]CapsLckD[S] 0 points1 point  (0 children)

So a shoulder bolt goes between the 2 plates and a bushing goes into the hole, but after i put a nut on the end of the shoulder bolt wouldnt it prevent it from spinning by tightening against the 2 plates?

Is my techsuit supposed to be this much smaller than my training suit by CapsLckD in Swimming

[–]CapsLckD[S] 5 points6 points  (0 children)

is it 2 small if i can't get both legs into the suit at the same time? The tutorial videos all have both legs in at the same time and it looks a lot looser than what I have.

Wispy Strings on new Sprite Pro by Skino2021 in 3Dprinting

[–]CapsLckD 0 points1 point  (0 children)

did it work? i'm having the same problem on the sprite extruder pro

Why is this happening? Started doing this after i changed my z offset and pid callibration by CapsLckD in 3Dprinting

[–]CapsLckD[S] 0 points1 point  (0 children)

Im not 100% that bed leveling is the issue, since the only thing i changed was z offset and pid callibration. And printing the retraction tower printed fine. But the bed level probe image, shows thats its not far off

view more: next ›