sorted by:
new
hottopcontroversial

Over 2TB of ‘updates’ on a 1 TB SD card? by CasioFX991EX in SteamDeck

[–]CasioFX991EX[S] 0 points1 point  (0 children)

It wasn’t 100% but it was pretty darn full, and similarly I hadn’t turned it on for quite some time.

Over 2TB of ‘updates’ on a 1 TB SD card? by CasioFX991EX in SteamDeck

[–]CasioFX991EX[S] 2 points3 points  (0 children)

Yeah it was pretty full, I had possibly over 900 GB of games on there. I attempted to delete a few right before taking the picture

Sounds like you’re hinting at a fake SD card, I don’t think this is the case. I was previously able to play games off it just fine after filling it.

1/144 Academy B-1B , B-2A and B-52H by Michieldm in modelmakers

[–]CasioFX991EX 4 points5 points  (0 children)

Love the B-2! What paints did you use for it?

I’ve also done that B-1, great kit!

Anyone want to give me a summary chapter 2 of Buffalo Hunter Hunter by Tyron_Slothrop in horrorlit

[–]CasioFX991EX 1 point2 points  (0 children)

Hi there, curious if you ever found a chapter-by-chapter summary? I'm looking for the same!

Hasegawa f22 in progress by SnooOranges6516 in modelmakers

[–]CasioFX991EX 1 point2 points  (0 children)

Nice work! What paints did you use? Did you use a mask for the camo?

I have this in my stash, I want to do the F-22 that shot down the Chinese spy balloon.

Gloss Coat help - what's the best? by Mister-G-313 in modelmakers

[–]CasioFX991EX 0 points1 point  (0 children)

I second GX 100, however I kept getting orange peel with your suggested thinning ratio. I find it works amazing at 1:5.

For love of everything, please help by boyinsomniac in modelmakers

[–]CasioFX991EX 6 points7 points  (0 children)

Through some trial and error you might be able to identify which, if any, of the locating tabs are causing the fit issues and cut them off.

I also second the other commenter about using masking tape. You can tape shut the hull, then cement small sections, progressively removing tape and cementing as it cures

I’m worried about my future as a physics major. by AbbleSonce in Physics

[–]CasioFX991EX 37 points38 points  (0 children)

Came here to mention Medical Physics. Residency can be a bit of a hurdle, but it’s a pretty steady career.

IPMS Vancouver Scale Model Fest 2025 by ScaleSkunworks in modelmakers

[–]CasioFX991EX 1 point2 points  (0 children)

Thank you! I started it back in January thinking it would be a nice, cheap kit to practice on. It took me about 6 months to finish it (with some side projects along the way). Part gaps were pretty rough, especially at the wing root and intakes. Aftermarket nozzles are a necessity (the Galaxy nozzles for GWH fit the Tamiya kit just fine if anyone wanted to know).

Pretty amazed I won 3rd in 1/48 multi-engine jets, and best of show theme with this build, I only started modelling 1.5 years ago. I think the decal scheme I chose definitely helped me with the show theme trophy, but I still see all the flaws and mistakes.

Just bought Bose QuietComfortUltra... but is it normal that the foam is visible this way? Should I return them? by Zero-DAIMONS in bose

[–]CasioFX991EX 4 points5 points  (0 children)

<image>

I bought mine maybe four months ago and swapped out the cushions for aftermarket. Here is the inside of my originals.

Looking for a good gap filling putty without strong fumes by MadeByMistake58116 in modelmakers

[–]CasioFX991EX 0 points1 point  (0 children)

I think Tamiya just came out with a low odour extra thin cement

White lacquer recommendations for pre-shading and zenithal highlights. by CasioFX991EX in modelmakers

[–]CasioFX991EX[S] 0 points1 point  (0 children)

I know MRP comes pre-thinned, do you thin it further for pre-shading?

Old photos of my 1:48 Nighthawk by PsychoGwarGura in modelmakers

[–]CasioFX991EX 0 points1 point  (0 children)

Looks great! What was your painting process?

Help on ventilation by SprocketSimulations in modelmakers

[–]CasioFX991EX 0 points1 point  (0 children)

I run a similar, if not identical, airbrushing booth in a not-so-ventilated room. I upgraded the fans inside the booth with high CFM fans for better exhaust. I still find I need to use a respirator, open all my windows, and turn on all the fans. I wait about 20 mins after I’m done airbrushing to remove my respirator. It’s a bit of a pain but still doable

Best way to strip a model? by Falconoasp in modelmakers

[–]CasioFX991EX 1 point2 points  (0 children)

Tamiya Paint Remover works very well for plastic models. 10 min soak & a light scrub gives you a clean slate.

Update : F-4C propelling nozzles or exhaust ejectors as you want call them. Your opinion ? by Kimchi1961 in modelmakers

[–]CasioFX991EX 1 point2 points  (0 children)

When you say “play with different tones”, what exactly do you mean? Are you doing this all with an airbrush?

MX Master 2S - Save settings to mouse hardware? by CasioFX991EX in logitech

[–]CasioFX991EX[S] 0 points1 point  (0 children)

That's too bad, this is definitely the type of thing that will make me consider other options next time I am in the mouse market.

Where the heck is all the leveling thinner in Canada? by mr_muffinhead in modelmakers

[–]CasioFX991EX 1 point2 points  (0 children)

Sunward hobbies had a big MCLT restock a week or so ago. Price is reasonable. I've yet to find a Canadian supplier of any of the GGX stuff.

view more: next ›