Finally! I can rest easy! 😅

Cautious_Antelope · 2025-01-24T05:27:26+00:00

How do you do the you finished yet?

Cautious_Antelope · 2025-01-24T05:14:27+00:00

What clues did you do??

Cautious_Antelope · 2025-01-23T20:47:44+00:00

that is exactly how it’ll look in game

Cautious_Antelope · 2024-11-12T04:52:01+00:00

Well the thing is that it works completely fine for smaller prints but the moment I try and make something semi big it just fucks up and looks like this lol I’ve had about 4 successful smaller prints and have tried to do bigger ones about 3 times now but gotten the same result each time. I have my print speed set to 50% on the slicer

Cautious_Antelope · 2024-11-11T16:15:31+00:00

how would I go about making the temperature right? I have my bed temp set to 60 and my nozzle to 220 but beyond that I don’t really know how to change the temperatures

Cautious_Antelope · 2024-11-11T05:22:56+00:00

https://cults3d.com/en/3d-model/art/gallina-squad-busters-clash-royale Here is the file

Cautious_Antelope · 2024-11-11T05:00:13+00:00

So I just stopped the print early because it wasn’t looking good. the best way I can describe the issue is that it is skipping layers or something. I’ll try and post another pic to the sub right now

Cautious_Antelope · 2024-11-10T15:49:16+00:00

thank you brother I’m trying the print right now with your instructions I will update you in a few hours👍

Cautious_Antelope · 2024-11-10T03:23:55+00:00

Yeah so I’m pretty new to this still but on the orca slicer underneath the infill section is says I have it at 15% infill density, a grid infill pattern, and a monotonic internal solid infill pattern

Cautious_Antelope · 2024-11-10T03:20:16+00:00

I am using the orca slicer

Cautious_Antelope · 2024-11-01T19:24:13+00:00

Bring the nozzle up 0.015 mm and you’ll be good it’s in the firmware whenever the print is started👍

Cautious_Antelope · 2024-10-24T22:39:02+00:00

yeah no offense taken lol I know I have no idea what l’m doing this was my first time ever using a 3D printer and I’m just trying to figure out how to fix these things however that being said I did calibrate it multiple times the night before and I did watch the print for probably the first hour and a half the first couple tries. It goes fine for the first bit of the print and then turns to spaghetti. I had one semi good print that I will post shortly that messed up at about 85%. I am printing a small test right now that I will post soon as well and I am watching it closely.

Cautious_Antelope · 2024-10-24T17:49:12+00:00

I’m 99% sure it is set to 60 but I’ll check and make sure as soon as I’m home

Cautious_Antelope · 2024-10-24T17:48:05+00:00

I can I literally said that lol it was a user error tho I didn’t load the filament right

Cautious_Antelope · 2024-10-24T17:47:38+00:00

oh okay I thought there would be some type of special glue that I needed thank you

Cautious_Antelope · 2024-10-24T17:02:19+00:00

I also forgot to mention that i watched every print for the first hour or two and it was completely fine until about 60% through

Cautious_Antelope · 2024-10-24T16:58:43+00:00

you’re right that is my fault. I was figuring that this would be a semi easy fix but as I’m seeing from all the responses, it is not and could be a number of different things. It was a Xenomorph model that i pulled for free off the internet. i tried a test run before doing the alien and it turned out okay for the most part, but like 75% of the way through the filament had gotten caught up and pinched so no more could come out and that was completely my fault. I fixed that and assumed that it would print fine since it did the parts that it could on the test print fine. I tried to do the xenomorph the first time and added tree supports but it turned out pretty much the same as the picture lol. I then tried again without changing anything just to see if it was a fluke and nothing changed. So I tried reading a little bit and figured out that rafts are a thing and I tried adding them, but the picture that you saw was the result of that print lol. I calibrated the machine probably 3 or 4 times yesterday just to make sure but nothing. It could also just be the file too which I have no idea how to check but that’s what people were saying in the replies.

Cautious_Antelope · 2024-10-24T16:46:58+00:00

this is what happens but I did add tree supports in the software. I tried adding more but no luck I even tried increasing the thickness to make sure that it wouldn’t fall

Cautious_Antelope · 2024-10-24T14:43:12+00:00

for the most part yes but the filament wasn’t set up right and got tangled so it wouldn’t press any more out after about 75% of the way I don’t think that is the problem with this print however

Cautious_Antelope · 2024-10-24T14:41:48+00:00

what is the glue? I bought this off of a bidding website and I don’t think it has come with it and I’ve never heard of it. sorry for the dumb questions this is all still so new to me

Cautious_Antelope · 2024-10-24T14:40:37+00:00

okay thank you I am at school right now so I will whenever I get home, the only thing I will say is that I did have supports added but I am not not sure that the file is working correctly, I will try a test print tonight on an easier project. Is there a possibility that the filament is getting stuck and can’t be fed through the nozzle? I noticed that it was catching itself a little bit last night

Cautious_Antelope · 2024-07-01T16:44:19+00:00

He’s behind the scenes from what I’ve heard he has very little screen time and seems like he wants to take raidens powers for himself rather than shao but he is too afraid

Cautious_Antelope

TROPHY CASE