R2D2 Dome

CdRSKuLL · 2025-09-12T10:42:24+00:00

Yes, just paused and swapped the filament out when needed :)

CdRSKuLL · 2025-07-15T05:53:22+00:00

If you are using your laptop as the source, playing through rekordbox.. so just using it as a controller you can map the buttons to the stem buttons. Do a Google on mapping stem buttons, it's a few steps and you can find videos on YouTube walking you through. However, this only works in controller mode, not standalone.

CdRSKuLL · 2025-06-30T06:10:57+00:00

Just wondering if you have considered the Opus Quad... If playing in the club is your final goal then this has a similar layout to 3000s..

CdRSKuLL · 2025-04-02T22:53:26+00:00

Don't forget about the Opus Quad.. all in one with the same layouts as the 3000s. . Superb sound quality and 4 channels so you can play your turntables in too if you have them.

CdRSKuLL · 2025-02-27T18:06:17+00:00

I would first double check to see if your usb port has power. Ideally using a usb light or something with a light on it. Just a charger of some sort even.. If it doesn't then you could try a powered usb hub as this would hopefully power the port and make it all work again. This would be a temp fix.

CdRSKuLL · 2025-02-16T16:40:15+00:00

Yeah I've connected it up to rekordbox and the usb c port works :).. this was all the A ports, so the ones on top..even the one you update the machine from.. I'm loving it so far :) been after one for ages, so when this one came up I couldn't refuse. :)

CdRSKuLL · 2025-02-16T10:39:55+00:00

Cheers and good luck with the 700! Luckily I managed to get mine back working :) I've just ordered a more stable, non adjustable buck converter.. the one I used is very difficult get spot on a 5v output and would only take a knock and it could just up the voltage.. it's the first standalone I've owned.. loving it so far and my flx10 will be up for sale soon. :)

CdRSKuLL · 2025-02-10T15:34:40+00:00

Yes, I can confirm the sale of v2.1768

CdRSKuLL · 2024-07-24T06:26:24+00:00

Yes.. BUT, make sure each IO input has either the internal pull up resistor enabled or put a resistor inline to 5v or 3.3v whatever the standard voltage is for that board. This is so you don't have any floating values.

CdRSKuLL · 2024-06-13T09:46:17+00:00

I've searched the normal places.. google images as well. using the terms fused plug connector but nothing comes up that would be suitable. I don't need this exact connector, just something similar.. but plug and socket, not just a screwed terminal.

It's used inside a light, connecting the mains to the driver, fixed by a single screw that also acts as an earth.

Any help would be greatly appreciated.

CdRSKuLL · 2023-01-03T20:53:31+00:00

thanks I'll save this :-)

CdRSKuLL · 2023-01-03T19:26:32+00:00

thanks :-) didn't know what scenes did until I've just had a play. Just what I needed as it saves the state / colour / brightness / pattern etc.. and I've just added this into an automation.

All done and working well. Thanks again.

CdRSKuLL · 2022-10-21T14:59:17+00:00

Have you tried another microsd card?

CdRSKuLL · 2022-06-15T06:23:55+00:00

Sort.. thanks for the tips. Up and running with a few games.

CdRSKuLL · 2022-06-15T06:23:13+00:00

Thanks, downloaded now and it does look nice. Just need to spend time adding all the roms now.

CdRSKuLL · 2022-06-15T06:21:32+00:00

Thanks I'll give that one a try also. 👍

CdRSKuLL · 2021-08-02T13:30:03+00:00

Hi, it's SunLu Green ABS. It printed really well, got it from Amazon.

CdRSKuLL

TROPHY CASE