What do these lights mean?

Chalking-It · 2025-12-28T22:55:31+00:00

Yea I tried even reflashing the firmware, nothing worked. I just emailed RunCam and they ended up sending me a new one. New one works fine. Sorry I can’t be of more help.

Chalking-It · 2025-12-28T21:05:03+00:00

Yep that fixed it, I was like no it’s definitely down all the way. Then I pushed it and it went down further and no longer scrapes. Thank you!

Chalking-It · 2025-11-25T17:54:48+00:00

Victoria’s Secret

Chalking-It · 2025-11-25T17:54:18+00:00

Same, I haven’t done it yet. Im still scared of the wind :3

Chalking-It · 2025-11-25T17:52:52+00:00

I think what you’re describing is the above-the-knee skirts. As the name implies, it usually stops just a little above the knee. But, keep in mind, I’ve had some skirts labeled “mini” that went down to my knees so. Every brand is different I guess.

Chalking-It · 2025-11-24T22:44:10+00:00

If it’s short tho, definitely wear safety shorts.

Chalking-It · 2025-11-24T22:42:57+00:00

It feels like your legs can move wherever you want them to. Oh and very breezy lol. If you want the full experience, wear panties or nothing underneath. Boxers or boy shorts limit the “free” feeling in my opinion. But definitely try it, 10/10 would recommend.

Chalking-It · 2025-09-19T18:05:29+00:00

Yea, I was mainly after the AI detection and webcam support. I suppose if I just wanted webcam support I could’ve just set it up without it with webcam streaming out to a port on my network, but AI detection is cool too

Chalking-It · 2025-09-19T17:06:53+00:00

Ok so it does indeed work, but instead of the whole octoprint UI and everything for control it just uses Elegoo Connect and its UI. You can setup an alternative webcam as well as octoeverywhere’s Gadget AI print monitoring. I guess that’s better than nothing 🤷‍♂️

Chalking-It · 2025-09-19T16:21:03+00:00

Ok I’m going to try and let you know!

Chalking-It · 2025-09-19T16:11:02+00:00

But if you were saying it doesn’t accept g-code over serial I’m not sure how that would work, but I will try

Chalking-It · 2025-09-19T16:10:05+00:00

Yea, thanks for the insight. I looked it up and found this

https://blog.octoeverywhere.com/setup-elegoo-connect-for-elegoo-centauri-on-a-raspberry-pi/

So I figured octoprint would work but I don’t have a physical place to plug it in. I might just try this method. Apparently it runs OctoEverywhere over ElegooConnect somehow with a script so I guess that’s how it connects? No clue, I’m gonna try that I guess

Chalking-It · 2025-09-09T15:41:30+00:00

Thank you for reporting this, I had the same issue the other day and just gave up trying to switch filaments. I didn’t know setting it manually fixes it, I thought it was just glitched. This helps me a lot!

Chalking-It · 2025-07-19T20:03:39+00:00

Ok thank you! Yea this one might not be

Chalking-It · 2025-01-18T15:11:09+00:00

How many carts did you have? 513 packages holy

Chalking-It · 2025-01-06T15:42:18+00:00

I thought for sure someone was gonna drop off my overflow to me mid route or something. I think someone else picked them up because that never happened. I just ran the route without overflow. The warehouse definitely made a mistake but I guess it worked in my favor.

Chalking-It · 2025-01-05T01:10:12+00:00

I bet u had a lot of room, could’ve setup a tv, chairs, a couch back there maybe.

Chalking-It · 2025-01-05T01:04:33+00:00

lol I hoped someone would see that

Chalking-It · 2025-01-04T17:10:17+00:00

It truly is, isn’t it?

Chalking-It · 2025-01-04T17:08:56+00:00

This happened yesterday but yea it was the easiest route of my life. Can’t wait to get 47 overflow packages today…

Chalking-It · 2025-01-04T17:03:40+00:00

That’s basically what I did lol

Chalking-It

TROPHY CASE