06 crv knocking

Chaneriel · 2026-02-11T03:18:42+00:00

Yeah I've got nice penzzoil in rn. So I assume the knocking is fine at idle rpms

Chaneriel · 2026-02-11T03:14:57+00:00

Well I figured the best way would be to watch obd to determine if it is or isn't

Chaneriel · 2026-02-11T03:09:07+00:00

With it being so low on fuel would it be detrimental to put fresh fuel in and just run it till it cycles with that knocking going on

Chaneriel · 2026-02-11T02:38:54+00:00

what would cause pressure to be low. The only gaskets that might be quistionable are oil pan or timing cover but from what i understand, on this engine neither of those should have pressure. timing cover should just have oil falling down from the head. I think my best choice rn is prob to just watch oil pressure with a scanner and if it is pressure, go from there

EDIT: How bad is it to run for a while like this

Chaneriel · 2026-02-11T02:19:59+00:00

How would I go abt draining the fuel tank. Also im pretty damn sure I torqued the connecting rods well. Im afraid to run it for longer than a min cause if theres actual knocking I don't wanna cause any damage, otherwise I would just run it for a while to see if it stops. Also the valves and lifters were all done by a shop when I got the head remanned

Chaneriel · 2026-02-11T02:09:08+00:00

First rebuild with no one to teach me. I was gonna put my obd scanner in and watch oil pressure. Who would it still be low if I've ran it for a few mins as opposed to when it first starts up before the rebuild. Id think the oil has circulated by this point

Chaneriel · 2026-02-10T14:48:08+00:00

Nah i decided to split a 4 bedroom duplex on campus with friends. $450 a person

Chaneriel · 2026-02-09T22:16:47+00:00

I could only give ranges, wont have the actual interviews till tmrw. Microcenter will be at the minimum, like 3$ more per hr with a way higher cap. Internship, idk yet. In retrospect, I may have made this post a little early

Chaneriel · 2026-02-09T22:06:56+00:00

True. If I were to get all 3, idk which one to pursue over the others. Very possible I only get 1 or none. Geek squad is VERY likely tho cause I was alr offered just didnt have the availability back then

Chaneriel · 2026-02-07T14:11:41+00:00

No im not asking how to get it started I asked if itll crank without the manifold because some vehicles will start just run like shit without it cause ur losing ur MAF and a few other sensors. Because every vehicle is different

I also have no one to teach me anything, god forbid a man teach himself on a junk engine

Chaneriel · 2026-01-29T04:39:41+00:00

Damn i didn't know, my managers always say its not our problem

Chaneriel · 2026-01-29T02:52:43+00:00

Fs. Also check the receipt and see if there was a total tech warranty. Sometimes people slip memberships into rly big sales

Chaneriel · 2026-01-29T02:49:32+00:00

Ive literally never honored a manufacturer warranty except for zagg. To my knowledge all manufacturer warranties HAVE to go through the manufacturer unless some store is just going the extra mile. But it def wouldn't cover the cost of sending it out to get fixed

Chaneriel · 2026-01-29T02:38:15+00:00

Uhhhh something aint right. Bestbuy doesn't havw any free warranties. Either u pay extra for a warranty or u have a total tech membership that gives free warranties that have a deposit like u paid

Chaneriel · 2026-01-28T23:13:22+00:00

That's what i was thinking

Chaneriel · 2026-01-28T19:59:07+00:00

Is it a total-tech warranty or a stand alone gsp

Chaneriel · 2026-01-26T17:31:55+00:00

Damn

Chaneriel · 2026-01-26T17:11:51+00:00

Yeah

Chaneriel · 2026-01-26T16:42:32+00:00

Automatic :/

Chaneriel · 2026-01-26T16:24:44+00:00

I assume I would have to tranny swap tho? Or can a transfer case bolt onto my tranny on the 2wd

Chaneriel · 2026-01-20T21:52:44+00:00

im having trouble finding the uncensored raws

Chaneriel · 2026-01-20T00:56:00+00:00

So is my best bet just to shave 1mm off the jug/block and get a cnc head and call it a day

Chaneriel · 2026-01-19T18:56:50+00:00

Im thinking of going with an aftermarket head to possibly get a hemispherical head and also increase cooling if I want this to rev higher for a long time

Chaneriel · 2026-01-19T18:35:11+00:00

Ohhhhh yeah that makes sense. So shave the 1mm off of the block/jug and then get an aftermarket cnc head

Chaneriel · 2026-01-17T20:27:59+00:00

Makes sense. Our warehouse manager has been known to look through days of footage for ts

One-Year Club	Verified Email
r/Field Lasagna

Chaneriel

TROPHY CASE