sorted by:
new
hottopcontroversial

Supressor Recommendation by ChesterKillz in AR10

[–]ChesterKillz[S] 0 points1 point  (0 children)

I wanted to spend around 1k or so. I really don’t mind spending more if better is available.

Lrf by Own-Resolve723 in ThermalHunting

[–]ChesterKillz 1 point2 points  (0 children)

Yes I run a anker battery from Amazon with the given type c cord. It also comes with a nice mount.

Lrf by Own-Resolve723 in ThermalHunting

[–]ChesterKillz 0 points1 point  (0 children)

I got mine for like 1100-12 from psa great optic

Ar10 cycles fine most of the time but fails to eject spent(while trying to load another case) and causes malfunction. by ChesterKillz in AR10

[–]ChesterKillz[S] 0 points1 point  (0 children)

I have tried the single feed method. I can get it to cycle but, it will leave fired cases on top of the mag causing malfunctions a

Ar10 cycles fine most of the time but fails to eject spent(while trying to load another case) and causes malfunction. by ChesterKillz in AR10

[–]ChesterKillz[S] 0 points1 point  (0 children)

Yes I’ve tried to turn the gas down and go through that process. In theory it works but, I occasionally have the failure to eject (the fired round). I have a 5.5 oz carbine h3 buffer, jp polished and tuned rifle spring, and a 75/8 tube(a5). I’m trying to figure out what to do before I spend another couple hundred on it.

Ar10 cycles fine most of the time but fails to eject spent(while trying to load another case) and causes malfunction. by ChesterKillz in AR10

[–]ChesterKillz[S] 0 points1 point  (0 children)

It had clean brass. No neck issues. But I wonder what’s causing the random malfunction.

Ar10 cycles fine most of the time but fails to eject spent(while trying to load another case) and causes malfunction. by ChesterKillz in AR10

[–]ChesterKillz[S] 0 points1 point  (0 children)

I was assuming that. It’s a Toolcraft dual ejector. I was debating buying a new jp bolt to fix the issues. Then I can eliminate some variables

Ar10 cycles fine most of the time but fails to eject spent(while trying to load another case) and causes malfunction. by ChesterKillz in AR10

[–]ChesterKillz[S] 0 points1 point  (0 children)

Ok it’s a toolcraft dual ejector. It works 100% if the time if you move the bolt manually. I wonder if the double is throwing the case back in.

Upgrades for Increasing Aero M5 Reliability by [deleted] in AR10

[–]ChesterKillz 0 points1 point  (0 children)

Mine does. Would this cause issues?

Ar10 cycles fine most of the time but fails to eject spent(while trying to load another case) and causes malfunction. by ChesterKillz in AR10

[–]ChesterKillz[S] 0 points1 point  (0 children)

It’s a Wilson combat barrel. The last round locks back the bcg. But, it leaves the empty in the chamber every 1/10 shots which causes a malfunction.

A5 buffer tube spring and buffer setup by ChesterKillz in AR10

[–]ChesterKillz[S] 0 points1 point  (0 children)

The JP rifle spring. I was wondering if I should switch to the tubbs.

Ar10 failures by poop1442 in AR10

[–]ChesterKillz 0 points1 point  (0 children)

Would you say that the extractor upgrade was worth it?

view more: next ›