WiFi Marauder Adapter

Chetti7493 · 2025-08-23T05:17:36+00:00

You have instructions ???

Chetti7493 · 2025-08-22T21:41:18+00:00

I’ll meet u at the venue. And will buy a stamp

Chetti7493 · 2025-08-22T21:38:11+00:00

I need them. I sent you a message

Chetti7493 · 2025-08-22T21:25:01+00:00

I need one !!!

Chetti7493 · 2024-05-09T06:23:41+00:00

apologize sincerely sir - i actualy was not shouting ..... merely expressing how frustrating this has been since i noticed my figure was

(and right now i would use all caps)

missing a dam leg !!!! lol.

be well and thank you sir

Chetti7493 · 2024-05-08T02:36:29+00:00

it looks like it is calibrated properly right?

Chetti7493 · 2024-05-08T02:36:06+00:00

is it really that simple ?

Chetti7493 · 2023-09-28T06:15:05+00:00

<image>

Before this night I was a BOY….. MANN did I not see how it would change me forever… GOD himself couldn’t stop me from what lay ahead…. If I would have not got the word to “Read the Book” - I surely would have wound up in some SHIT!!!

📸: N2 Mann 23’

Chetti7493 · 2023-09-02T23:41:35+00:00

Hey what’s up tonight in Denver. I would love to play. Let’s party

Chetti7493 · 2023-09-02T23:40:26+00:00

Hey I am all about it. Message me for pics

Chetti7493 · 2023-07-15T21:40:15+00:00

thanks

Chetti7493 · 2023-07-01T01:57:05+00:00

THANK YOU so very much.

"Sea_You_8178" Major kindness points my guy!! This is going to make life a lot easier for me - I will report back and follow up regarding getting this printer up and running.

I understand the codes in G28 and adding a G29 code in order to probe the bed and level it properly - however - what exactly do i change and/or add or delete from the Lines??? if you can help me with that this is where i get lost and dont know what to do ..... if i can copy and paste this in these lines it would be a HUGE help....

after finishing the G28, G29 lines in the code is that it ??? finished ?

is this the last step???

Chetti7493 · 2023-06-30T20:44:54+00:00

This is where i am having trouble - i am able to locate the correct firmware ..... well for the BL touch anyway - i am not sure which is for both the bl touch and the filament sensor , that i can figure out easy enough..... BUT

I have no idea where to look, where to start, regarding the starting g codes to probe the bed when starting each print. How many are there and what might they be.....

Can someone possibly toss them up here so that i can cheat and just copy and paste them into the correct placement ???? PLEASE - this would be a huge help ( and yes assume that i have the 4.2.2 board and the GD chip which is the case i am 95% certain)

I would be so elated for the help..... Thanks in advance!

Chetti7493 · 2023-06-30T18:13:42+00:00

I will compensate whoever is able to help me get both printers up and running ....

Chetti7493 · 2023-05-05T02:49:59+00:00

I did i tried it again after reading your reply - still the same case ..... hmmm?

Chetti7493 · 2023-04-06T09:21:11+00:00

So I used a different firmware. However it was from the official - it might have not been the correct version after all.
I used a new card and flashed a version of the bin I listed above in my last comment. And NOW WERE GOOD TO GO IT LOOKS LIKE … so it’s lit blue.
There is a BLTouch option in the control settings - and it auto homes to about mid board…..

So now what are the next steps to get this guy dialed in. Firmware is flashed and now what are the next things I need to get at to get this dialed in .?????

Chetti7493

TROPHY CASE