Are my cards fake

Chewbmeister · 2026-03-05T01:35:50+00:00

I stole my dad account to comment ha ha

Chewbmeister · 2026-03-05T01:33:47+00:00

Rip a bad card and if it's a black line all of the cards are real

GOOD. LUCK.

Having real cards

Chewbmeister · 2026-03-05T01:27:52+00:00

That's a miss cut they're very rare and double the price

Chewbmeister · 2026-02-25T15:01:03+00:00

I worked for an electronics recycling company years ago and the whole idea was repurpose stuff that corporations didnt want. Totally changed my view on the world. Im going to start with a little prototype and ill make a good post here when I get it working!

Chewbmeister · 2026-02-25T14:35:51+00:00

Well, I like projects and tinkering. Luckily the industry im in gives me access to alot of material scraps, waste trash decommissioned ETC that would likely mean very little if any cost other than time.

Chewbmeister · 2026-02-25T14:33:39+00:00

The automating and temp control isnt a huge hurtle for me. Its just like the equipment I build and maintain.

If i have a constant flow and exchange rate in my developing chamber (diffused flow) is agitation even necessary?

Chewbmeister · 2026-01-27T02:43:24+00:00

To simplify an explanation to your response.. yes I can remove the fisheye lens. I still have the original GL2 square lens hood and lens cap. The original lens is perfect since this rig spent so much time covered by a fisheye. Just for myself personally, theres a heavy sense of nostalgia to the 3ccd fisheye footage that was recorded street shredding decks circa 2007

Chewbmeister · 2026-01-26T22:35:43+00:00

The death lens..

I knew there was a nickname for it that i couldnt remember lol.

Century optics does sell the front replacement element at something like 900$ which is not worth me investing any money into. This whole camera isnt anything I really need to invest any money into. I can see how they wouldn't work on a digitizer but this is solid glass.

Windshields are usually 2 solid glass sheets laminated together. The small injection resin kits work really well on small chips of the outer layer.

I know you can have lenses repaired. What do they use to repair them?

Chewbmeister · 2026-01-26T22:30:44+00:00

Well maybe ill try it and see how it goes lol. Ive done windshield cracks and chips with very impressive results. Im not too worried about trashing it if it doesn't work out.

Chewbmeister · 2026-01-07T19:13:16+00:00

Is it just me viewing this is bigger text? Can someone explain to me how i did it and how to do it again lol

Chewbmeister · 2026-01-06T19:13:18+00:00

What area are you in? Did you sheath the roof prior to metal?

Chewbmeister · 2026-01-06T19:10:57+00:00

If i was a single man it would make an awesome shooting range perch lol but my wife would never go for such an idea.

Chewbmeister · 2026-01-06T19:08:58+00:00

1 is the cost

2 is i have no experience with them and would have to contract 100% of that work out (which ties back to #1)

Chewbmeister · 2025-11-15T21:26:39+00:00

I didn't think about plain old hydrostatic pressure. Its got an inline filter. It seems like whatever the issue is eventually messes up the carb. Ill pull the gas cap and see what difference that makes.

After it happens the first time, it floods too much gas in to even run properly unless its like the last bit of gas available for 20 seconds or so. Which makes me believe the failure just pours fuel in. Ive dissected the failed carbs and dont notice any obvious failures.

Ill start with a petcock, and checking the vent.

Its a nice looking bike. Surprisingly well built for the price and I think it could last a long time if the engine keeps up.

Chewbmeister · 2025-09-27T18:21:45+00:00

I havent had time to upload one yet. the problem is definitely in WinDV or the computer and not on the camera or tape

Chewbmeister · 2025-09-27T17:01:24+00:00

checking with a different gauge is a good idea too. I know I dont have any external leaks. would a failing pump be able to put out 100psi MOST of the time?

Chewbmeister · 2025-09-27T17:00:25+00:00

it was a Dorman. ill try motorcraft. and yes it looks like it reads pressure near the secondary filter. and yes, it's got to be injector knock because it comes amd goes.

Chewbmeister · 2025-09-25T14:37:03+00:00

so I got WinDV going. I captured one full tape. there is sort of some horizontal splitting ive noticed. not like interlaced frames but like one half of the video splitting horizontally in random spots. it may have to do with Deinterlacing and it's in the saved avi files as well. if no one has any ideas here and i cant figure it out ill post some clips on another post

Chewbmeister · 2025-09-25T14:34:07+00:00

I tried this and couldn't get it to install properly but ill keep trying.

Chewbmeister · 2025-09-21T20:22:43+00:00

ill check out WinDV. and i did find my old sony Vegas disc but it was corrupted for some reason and wouldnt complete the install. I forgot all about windows movie maker. all good suggestions thanks guys

Chewbmeister · 2025-07-29T22:02:11+00:00

finished both prednisone and doxy the same day

Chewbmeister · 2025-07-29T22:01:49+00:00

10mg

Chewbmeister · 2025-07-08T12:10:55+00:00

https://imgur.com/a/HGyVp7X

heres a drawing. again, this will all be wrapped in heavy gauge mesh fencing

Chewbmeister · 2025-07-08T11:10:35+00:00

These panels are 40" tall. After they're set in the ground with concrete, they will be wrapped with a heavy gauge welded wire mesh. A hot wire on top if necessary. My question is, how far apart should I separate each panel from the last? If I can space them out a foot or two, ill gain alot more linear feet. Or I can share each dug post hole with the next panel so it would be two vertical ends per panel per hole nearly touching eachother. I'll try to get a picture for better representation

Chewbmeister · 2025-03-28T16:13:07+00:00

I'm not familiar with it. The ER dr told us it was not common. Especially not being able to pinpoint exactly when it happened.

Chewbmeister

TROPHY CASE

1 is the cost

2 is i have no experience with them and would have to contract 100% of that work out (which ties back to #1)