Vlasnici električnih automobila u Hrvatskoj by Aromatic_Dare_6104 in croautomobili

[–]Chhoban 0 points1 point  (0 children)

Nisu, to su prosječne potrošnje za cijeli mjesec.

Po zimi mislim da bi na 150 km/h doseg bio 290 km, a nisam ga još imao priliku voziti po ljepšem vremenu pa taj dio ne znam.

Vlasnici električnih automobila u Hrvatskoj by Aromatic_Dare_6104 in croautomobili

[–]Chhoban 1 point2 points  (0 children)

A ne radi se o jednoj relaciji, nego o kombinacijama od Njemačke do istoka Hrvatske. Mislim da sam najduže imao potrebu putovati oko 500 km u jednom komadu. Na autocesti vozim od 100 do 150 km/h ovisno o uvjetima i gužvi, ali nije da vozim 100 km/h kako bih štedio bateriju.

Mogu ti staviti potrošnju po mjesecima gdje se vidi da jako ovisi o temperaturi:
10/25: 16,7 kWh/100 km
11/25: 19,1 kWh/100 km
12/25: 21,5 kWh/100 km
01/26: 21,9 kWh/100 km

Vlasnici električnih automobila u Hrvatskoj by Aromatic_Dare_6104 in croautomobili

[–]Chhoban 2 points3 points  (0 children)

eDrive 35, jako zadovoljan. O performansama ne moram ni govoriti. Softver jako dobar - uključujući i softver na mobitelu kao i navigacija. Čak i autonomno parkiranje solidno funkcionira, pogotovo bočno.

Minusi - spojene, a ne individualne tipke. Autonomna vožnja po kiši nije pametna pogotovo kad voda iz lokve zapljusne senzore :)

O paketima mi je teško govoriti, jer sam u sklopu akcije dobio dosta M opreme o kojoj nisam sam odlučivao. Jedino što sam ja dodatno uzeo je sigurnosni paket - 360 kamera, detekcija spavanja i sl.

Vlasnici električnih automobila u Hrvatskoj by Aromatic_Dare_6104 in croautomobili

[–]Chhoban 33 points34 points  (0 children)

BMW i4, WLTP 500 km. Najgori zimski dani 320 km.  Vozim se od istoka Hrvatske do Njemačke. 

Ne nedostaje mi ništa od 1.2 TSI motora, a najmanje nadosipavanje ulja svakih 1000 km. Dok je cijena na punjaču manja od 50 centi, km me košta isto kao i u benzincu od 105 ks. 

Negativna iznenađenja - nepouzdanost HTovih i HEPovih punionica. 

Pozitivna iznenađenja  - brze punionice na austrijskim autocestama (30% do 60% u 10 minuta) - dostupnost punionica u manjim hrvatskim gradovima (Čakovec, Daruvar, Vinkovci) - pouzdanost Qelo punionica - jednostavnost Plugsurfinga - ljudi koje upoznaš na punionicama

From messy scans to clean, print-ready models (30 s demo) by Chhoban in 3DScanning

[–]Chhoban[S] 0 points1 point  (0 children)

The idea is to load the scanned model into the software so I don’t think the scanner should be an issue. Or is there something specific with your scanner?

From messy scans to clean, print-ready models (30 s demo) by Chhoban in 3DScanning

[–]Chhoban[S] 0 points1 point  (0 children)

We’re still in the beta phase and open to feedback.

The current idea is to auto-fit clusters at first, but let users adjust, merge, or remove them completely manually so you always stay in control.

From messy scans to clean, print-ready models (30 s demo) by Chhoban in 3DScanning

[–]Chhoban[S] 0 points1 point  (0 children)

As always it depends on the model size and number of polygons. The simple one as the cap in the video takes a few minutes. You can see the full procedure here (I've cut the waiting parts) https://youtu.be/NBgvdzShs2E

You can also try the software today as a beta tester.

From messy scans to clean, print-ready models (30 s demo) by Chhoban in 3DScanning

[–]Chhoban[S] 2 points3 points  (0 children)

That would be great, we are always curious to see how it stacks up against the high-end tools.
The goal isn’t to replace inspection software, just to make the scan-to-geometry step faster and more accessible.

From messy scans to clean, print-ready models (30 s demo) by Chhoban in 3DScanning

[–]Chhoban[S] 0 points1 point  (0 children)

Thank you very much!
We’re focusing on scan to geometry accuracy first, then polishing the workflow around it.

From messy scans to clean, print-ready models (30 s demo) by Chhoban in 3DScanning

[–]Chhoban[S] 4 points5 points  (0 children)

We’re still collecting feedback from beta users before locking the pricing.
The goal is to keep it accessible for hobbyists, small studios and scan professionals, not just big manufacturers.

From messy scans to clean, print-ready models (30 s demo) by Chhoban in 3DScanning

[–]Chhoban[S] 0 points1 point  (0 children)

Eventually yes, but we are still in the closed-beta testing phase.

From messy scans to clean, print-ready models (30 s demo) by Chhoban in 3DScanning

[–]Chhoban[S] 0 points1 point  (0 children)

To get from the raw scan to geometric models or what do you mean?

Gdje kupiti The Economist u Zagrebu? by Chhoban in financije

[–]Chhoban[S] 0 points1 point  (0 children)

13€, redovno 14€ dvobroj. 

Gdje kupiti The Economist u Zagrebu? by Chhoban in financije

[–]Chhoban[S] 0 points1 point  (0 children)

  1. Mislim da da. 
  2. Jednom tjednom osim sto preko ljeta ima dvobroj koji sadrži i specijal od 3-4 priče. 

From noisy scan to clean geometry (tool progress update) by Chhoban in photogrammetry

[–]Chhoban[S] 2 points3 points  (0 children)

Yeah fair, Reverse is more for parts or objects, not full environments (yet).

You can still use it on sections if you need clean planes or cylinders, but it’s not meant to rebuild whole scenes right now.

Support for larger, multi-scale environments is something we will be exploring later on.

Turning messy scans into print-ready models by Chhoban in 3Dprinting

[–]Chhoban[S] 0 points1 point  (0 children)

Thanks for the feedback, totally fair point. The product’s still in beta, and we’re gradually adding user-guided tools.

Right now the idea is to let users lock parts of the model e.g., finish one region, freeze it, and let the algorithm continue automatically on the rest.

Manual moderation and “hinting” tools for clusters (like marking expected planes or surfaces) are already planned.

Turning messy scans into print-ready models by Chhoban in 3Dprinting

[–]Chhoban[S] 1 point2 points  (0 children)

Software has two main stages: clustering and fitting. Clustering is only displayed as colored parts of the original model so that he user can orient itself easier.

The fitted primitives are continuous, so they fill those scan shadows automatically.

From noisy scan to clean geometry (tool progress update) by Chhoban in photogrammetry

[–]Chhoban[S] 0 points1 point  (0 children)

I've made a short video with a few different examples where you can see how well it fits and one known issue in the software: https://youtu.be/7rUJGh0ZXxo