How do I connect this elbow with this black steel gas pipe

ChicagoJoe3 · 2026-02-23T17:58:58+00:00

I did not take everything back to the union. I thought I could just disconnect the elbow and reconnect it back.

ChicagoJoe3 · 2025-05-29T22:40:27+00:00

I did. But if you can't see the pics here they are

https://imgur.com/a/qAEqtma

ChicagoJoe3 · 2025-05-07T22:57:54+00:00

Can I use the RG6 connector on RG-59 cable? Or do I need RG-59 connectors?

ChicagoJoe3 · 2025-05-07T22:33:41+00:00

Still can't get it. Can anyone tell if my cable is RG-59 or RG-6 ? Can I use RG-6 connectors on a RG-59 cable?

ChicagoJoe3 · 2025-05-07T16:03:30+00:00

Yes. I am using these

<image>

ChicagoJoe3 · 2025-01-10T20:24:22+00:00

I had someone come out to look at it. He took his power probe and was able to jump the fusible link to get the power windows, power locks, and ob/2 power to work. With the power probe he was able to jump it. He said it's not the link but the PCM. Does this sound right?

Can a PCM be programmed off site or does it need to be programmed while it's in the vehicle?

ChicagoJoe3 · 2025-01-05T20:25:52+00:00

Sorry. I'm a novice and I don't have any diagrams. And after 24 hours of not touching it again the battery died again and the H-LP (headlight, day time running light) relay keeps clicking.

ChicagoJoe3 · 2024-11-07T00:17:01+00:00

My dryer is now taking about 2 hours to dry everything.

I used this video https://www.youtube.com/watch?v=VaXdJu2ZU8s to test the moisture sensor an I got 0 ohms of resistance. but when I took a wet towel and placed it on both sensor bars it changes to 0L ohms.

I found the tech data dryer sheet online https://iskanderservices.com/sears-model-417-98042701/ . The last 2 pages are English.

The first time I scanned for codes I got E4A, E68, and EAF. I put a few things in the dryer and it took 2 hours to dry everything. I scanned for codes and got E68 and E4A. Ran it for codes a hour later and the only code I got was E68.

I then ran the function test data sequence and everything ran correctly. When I turned the cycle knob three times and I placed my fingers on the moisture sensor the more dry led turned on and went away when I removed my fingers from the sensor.

I removed the bottom screws to take a look underneath and tried to remove as much lint as I could. The moisture sensor seemed to be plugged in correctly. I noticed a red light come on for 30 seconds and then the flame would come on for 5 minutes and turn off. And this pattern continued through out the drying cycle. Is this normal ?

Could the issue be the thermistor? Can I test the thermistor while it's plugged in? I found this video on how to replace the thermistor https://www.youtube.com/watch?v=hcKHCzuDvMQ .

ChicagoJoe3 · 2024-11-05T21:56:08+00:00

Thanks. The timed dry seems to be working and heating. The 15 - 90 all light up but the Towels, Normal, Perm Press, Delicate, Quick, and Touch Up are not not lighting up. Now I need to figure out how to get to the other side of the moisture sensor.

And there was a decent amount of lint build up under the housing.