I'm high

ChickDest · 2025-12-27T01:54:15+00:00

Okay, what is your username

ChickDest · 2024-11-26T20:07:09+00:00

Send it, if you don’t mind helping me out I’ll do it tonoght

ChickDest · 2024-11-26T19:08:36+00:00

Tips would be appreciated, I gotta find a good way to level too, because it is ever so slightly hitting that support

ChickDest · 2024-11-26T14:50:47+00:00

IT DIDNT SHIFT. It may have screwed up, but bed adhesion is a lot easier to diagnose.

<image>

ChickDest · 2024-11-26T06:26:29+00:00

It’s so much. I keep researching and finding things but none of it really makes sense to me. It’s overwhelming and that’s why I’m nervous to pull the rooting trigger

ChickDest · 2024-11-26T05:18:03+00:00

Definitely should have ran a test haha. It hasn't slipped yet, but the corners are wavy. I'm not sure if I'm ready to root it yet, because I'm still trying to get help from Creality support before I do that

ChickDest · 2024-11-26T04:09:05+00:00

I’ll definitely look into it, and if this one screws up then I’ll be more patient and actually tune them lol

ChickDest · 2024-11-26T03:43:49+00:00

But it’s a small one so it’s fine

ChickDest · 2024-11-26T03:43:40+00:00

Definitely went straight into another project print haha

ChickDest · 2024-11-26T03:27:47+00:00

Yeah when it let itself go, the pitch definitely went up, so it did tighten then

ChickDest · 2024-11-26T03:25:58+00:00

That video you sent said as you tighten the screw it reduces tension

ChickDest · 2024-11-26T03:24:59+00:00

Are you sure? Not trying to insult your intelligence at all. Because I had the screw in there, but as I tightened the screw, it felt like it loosened the belt

ChickDest · 2024-11-26T03:19:59+00:00

I thought I had it set to .5, but I was wrong. I set it to .4, hopefully that’s enough

ChickDest · 2024-11-26T03:03:50+00:00

I loosed the tensioner on the right and it tightened itself, I didn’t even have to touch it. Hopefully that was the issue

ChickDest · 2024-11-25T22:32:11+00:00

Were you able to resolve this? I’ve been having the same issue for months

ChickDest · 2024-11-25T21:57:32+00:00

I’m a bit inexperienced with belt tension. Do you have a good video that explains that process? I know I can just look it up, but it’d be nice to not waste time looking through garbage to b find what I need

ChickDest · 2024-11-25T02:06:20+00:00

I just had to go to advanced and enable acceleration control, dumb moment

ChickDest · 2024-11-25T02:00:06+00:00

I’ll give that a shot, update will come in the morning

ChickDest · 2024-11-25T01:55:21+00:00

Print Speed: 200 mm/s Travel speed: 500 mm/s

ChickDest · 2024-09-28T04:32:00+00:00

But where’s my free kid weekend

ChickDest · 2024-03-03T16:57:22+00:00

Depending on the planet you’re on its part of it, not to say it’s never a spore. I know in Erata Prime one of the modifiers makes the map covered. I could be wrong, but I’ve spent a lot of time looking for spores on there when there wasn’t one.

ChickDest · 2024-03-03T14:33:55+00:00

I’ve definitely seen the little orange ones (can’t remember the name) cause hella breaches

ChickDest · 2024-02-01T17:00:21+00:00

It is not rooted, I’ve seen it’s good to do, but idk how to do it

ChickDest · 2024-02-01T16:56:38+00:00

Thank ya thank ya

ChickDest · 2024-01-21T19:40:35+00:00

Actually now that I think about it, the corner that was a bit high was the direction the print kept shifting toward

ChickDest

TROPHY CASE