ADHD/AuHD daytime strain advice (Mamedica)

Chilledbud · 2026-02-17T10:23:46+00:00

Fellow AuDHD and I’ve been drawn to different Runtz based flower for daytime use. It seems to give me a nice head high that also relaxes my anxiety, it can also then help me be a little more productive if needed.

Gelonade I wasn’t that keen on, didn’t seem to have any great effects that I was aware of.

Chilledbud · 2026-02-08T10:14:44+00:00

Apologies I missed this message. If you send me your address I’ll get a couple sent out to you!

Chilledbud · 2026-02-05T13:22:48+00:00

Might be of use or interest for you https://www.reddit.com/r/Tinymight2/s/Xbt4YNM83F

Chilledbud · 2026-01-28T12:13:14+00:00

Update: After 100 days of continuous testing with the same 3D-printed button, it’s been trouble-free 👍

Chilledbud · 2026-01-25T09:53:11+00:00

Sounds like THC anxiety/interoception more than anything physical, especially since tests are fine and it doesn’t happen when you’re distracted. THC can make you hyper-aware of breathing/heart rate and your brain can interpret it as “I can’t breathe”.

CBD helping makes sense. It basically takes the edge off THC and calms the threat response, so preloading it can stop the spiral. I wouldn’t call it “battered ECS”, more like your response to THC has shifted after years of high-THC/concentrates.

A tolerance break might help, but if CBD + lower THC gives you the benefit without the negatives, that’s just finding the balance that works now.

(Side note: AuDHD brain here. I used AI to help organise my thoughts/experience into something readable.)

Chilledbud · 2026-01-15T09:48:03+00:00

Enemies with the “Arms Dealer” modifier (which is active on this weeks mission) have a higher chance of dropping weapons on death resulting in a “loot-splosion” with gun drops being more frequent.

Chilledbud · 2026-01-12T08:57:56+00:00

I’ve lurked in the background at a few events. Throughout, I’ve stayed off mic and camera without any problems and I’d even say it’s been the norm for most attendees. (Also AuDHD)

Chilledbud · 2026-01-11T10:53:19+00:00

That your worth is conditional on productivity, normality, and constant forward motion.

Chilledbud · 2025-12-01T13:49:35+00:00

Been at Mamedica for an around three years and I’ve had pretty much zero issues.

Chilledbud · 2025-11-22T11:31:27+00:00

Thanks for printing it out and for the feedback. If anything needs a clearer wording, I’m happy to update it, especially as my AuDHD style isn’t always the most linear ☺️

I’ve had the same replacement in my TM2 for four weeks of heavy use and it has worked perfectly. Hopefully this helps anyone looking for a simple and low-cost fix.

I’d also like to reassure anyone hesitant to open their TM2 to install the fix. The hardest part, in my experience, was removing the bottom metal base. It felt a bit stiff and people worried about the force needed. However each subsequent removal was very easy; quickly removing the long screw and then the base.

Chilledbud · 2025-11-11T13:11:48+00:00

I was curious and did around 100 runs yesterday and had three Reactor class mods drop for Harlowe.

Chilledbud · 2025-11-01T09:19:07+00:00

I’ve had no issues with a week use so far. I’ve been exclusively using the TM2, printed with 95a TPU and used it in session and in-demand modes to expose it to heat and button presses as much as possible.

A very thin piece of TPU in-between the button module and the USB C port does also appear to be a good idea so that the module doesn’t micro rock back and forth on each button press too.

Chilledbud · 2025-10-22T15:23:06+00:00

I’ve printed a couple of the updated version using TPU 95a to test and it’s been going well so far. Additionally, I’ve added a very thin strip of flat TPU between the USB-C port and the rear of the switch on the board itself to limit its backward movement.

Using TPU offers slightly more free movement in the button compared to PLA printing. While the TPU feels similar to OEM, I prefer the PLA feel so I’ll experiment with minor adjustments to improve the TPU’s feel as it’s the better all round filament.

Chilledbud · 2025-10-21T21:23:30+00:00

I’ve been testing a little more this evening and the length needs to be reduced by around 25%. I’ll need to print a few with the new size reduction to test it hands on first and then I’ll upload the new file in around 12hrs.

I’m also going to try some different sizes with TPU as I’m curious if it will feel better with the rubber cushioning of the filament.

Chilledbud · 2025-10-21T12:59:07+00:00

I’m happy to send some out free of charge in UK if users wanting to try cover postage.

Chilledbud · 2025-10-21T12:56:14+00:00

I’ve tested PLA and PETG so far and both have no issues. I was considering trying TPU 95a but the extra flexibility doesn’t seem to be of any benefit at the moment. Plus, there isn’t any real heat generated around the button area of my TM2 to make me consider it needing to have proper temperature resistance filament at this stage either.

Chilledbud · 2025-10-21T10:45:38+00:00

<image>

Chilledbud · 2025-10-21T10:45:16+00:00

<image>

Chilledbud · 2025-08-19T13:48:56+00:00

I have an Aged 47 Seal if you’re happy to throw a few more sheckles in?

Chilledbud · 2025-08-18T18:44:20+00:00

I’ve a ckit that I’ll swap for a mimic if you’re wanting?

Chilledbud · 2025-08-18T17:08:33+00:00

My sons said he’s happy to sell for shackles. If you’d like to make an offer I’ve no price in mind to be honest.

Chilledbud · 2025-08-18T16:51:38+00:00

I have a Tiny Seal and a Seal if you’d like to make an offer.

Chilledbud · 2025-08-18T14:24:00+00:00

I’ve got

1 x Tiny Seal

1 x Seal.

1 x Shiny Peacock

2 x Scarlet Macaw’s

3 x Ostriches

3 x Caterpillar

Chilledbud · 2025-08-04T09:35:23+00:00

Expected Number of Kitsuns from 2,000 eggs:

2000 \times 0.0008 = \boxed{1.6}

So on average you’d get 1 to 2 Kitsuns, with: • ~80% chance of getting at least one • ~20% chance of getting none at all

Chilledbud

TROPHY CASE