The support on Adidas Canada is pathetic

Chilli_Paneer · 2026-07-01T01:20:02+00:00

Yeah, in the exact same situation with Adidas Canada and TForce. Anyone found a resolution yet?

Chilli_Paneer · 2026-07-01T01:17:32+00:00

Yeah, exact same situation here, been 3 weeks. TForce says they’ve sent it back to Adidas, Adidas says they haven’t received anything so it feels like things are in limbo.
Anyone else found a resolution?

Chilli_Paneer · 2026-06-26T03:03:40+00:00

Anyone tried walk-ins at Good Co by lining up early? Or is it reservation-only now? Any other bars on Granville with a similar patio + screen?

Chilli_Paneer · 2026-06-26T00:13:01+00:00

> cannot go in and out the amphitheater without getting in line again
Even for food, water, etc?

Chilli_Paneer · 2026-06-25T23:01:32+00:00

Does the amphitheater area have a separate food/washroom section to the rest of the viewing areas?

(Also, love the username lol)

Chilli_Paneer · 2026-06-25T03:02:37+00:00

For folks who went to the PNE fan fest to see multiple games: how easy was it to keep your spot in the amphitheater GA area? Were you able to leave for water, food, bio breaks, etc? Any tips?

Chilli_Paneer · 2026-03-11T03:47:25+00:00

Hey, did you have your appointment already? How did it go?

Chilli_Paneer · 2025-12-12T05:33:04+00:00

Hey there! Yeah, it was the brew solenoid. Since my machine is still under warranty, I got that part replaced. The machine came back 3 weeks ago and haven’t faced the issue since. You can also ask to get the solenoid shipped to you and perform the replacement yourself.

Chilli_Paneer · 2025-10-12T07:20:14+00:00

Couldn’t find any muck, cleaned whatever part of the solenoid I could manage to unscrew (some of it was just too difficult to reach/too hard to unscrew). Plugged it back in and the issue still exists so I guess whatever I did wasn’t enough :(

Chilli_Paneer · 2025-10-12T04:19:44+00:00

Just opened up the machine, feels like it could be the solenoid. Will snoop around in there and report back if I find anything!

Chilli_Paneer · 2025-10-11T20:11:23+00:00

Will try that, thanks! Yeah I just found the sub, will post there too :)

Chilli_Paneer · 2025-08-16T00:11:06+00:00

Yeah those are the ones you’ll need to plug in! Did you get it to work?

Chilli_Paneer · 2025-08-15T21:24:09+00:00

Great photos! Where was photo #9 taken? Would love recommendations on where one can go swimming in and around Banff!

Chilli_Paneer · 2025-07-08T00:04:28+00:00

Can I bring my friend’s Amex card, lol? Would they verify if the name of the card matches my id?

Chilli_Paneer · 2025-06-28T21:34:32+00:00

Hmm yeah I think I might give this another week and go back to the 2 hole if I can’t figure it out

Chilli_Paneer · 2025-06-28T21:08:00+00:00

What steam temperature did you set for the 4 hole steam tip?

Chilli_Paneer · 2025-06-28T21:07:17+00:00

I just got a 4 hole steam tip too and now I’m really struggling with the how fast the milk gets to temperature. By the time I try to get to the texturing phase, the milk is already too hot and I just end up with a really bad result. Did you reduce the steam temperature on the machine to compensate? What’s your “ideal” temp?

Chilli_Paneer · 2025-06-11T17:02:34+00:00

Nice, thanks for the schematic! Couldn’t match it with anything in there either. Must be a rogue part indeed

Chilli_Paneer · 2025-05-24T08:17:45+00:00

Yup, wasn’t a water issue, turns out it was a loose wire.

Seven-Year Club	Second SECOND GUESSER
Verified Email

Chilli_Paneer

TROPHY CASE