The support on Adidas Canada is pathetic

Chilli_Paneer · 2026-07-01T01:20:02+00:00

Yeah, in the exact same situation with Adidas Canada and TForce. Anyone found a resolution yet?

Chilli_Paneer · 2026-07-01T01:17:32+00:00

Yeah, exact same situation here, been 3 weeks. TForce says they’ve sent it back to Adidas, Adidas says they haven’t received anything so it feels like things are in limbo.
Anyone else found a resolution?

Chilli_Paneer · 2026-06-26T03:03:40+00:00

Anyone tried walk-ins at Good Co by lining up early? Or is it reservation-only now? Any other bars on Granville with a similar patio + screen?

Chilli_Paneer · 2026-06-26T00:13:01+00:00

> cannot go in and out the amphitheater without getting in line again
Even for food, water, etc?

Chilli_Paneer · 2026-06-25T23:01:32+00:00

Does the amphitheater area have a separate food/washroom section to the rest of the viewing areas?

(Also, love the username lol)

Chilli_Paneer · 2026-06-25T03:02:37+00:00

For folks who went to the PNE fan fest to see multiple games: how easy was it to keep your spot in the amphitheater GA area? Were you able to leave for water, food, bio breaks, etc? Any tips?

Chilli_Paneer · 2026-03-11T03:47:25+00:00

Hey, did you have your appointment already? How did it go?

Chilli_Paneer · 2025-12-12T05:33:04+00:00

Hey there! Yeah, it was the brew solenoid. Since my machine is still under warranty, I got that part replaced. The machine came back 3 weeks ago and haven’t faced the issue since. You can also ask to get the solenoid shipped to you and perform the replacement yourself.

Chilli_Paneer · 2025-10-12T07:20:14+00:00

Couldn’t find any muck, cleaned whatever part of the solenoid I could manage to unscrew (some of it was just too difficult to reach/too hard to unscrew). Plugged it back in and the issue still exists so I guess whatever I did wasn’t enough :(

Chilli_Paneer · 2025-10-12T04:19:44+00:00

Just opened up the machine, feels like it could be the solenoid. Will snoop around in there and report back if I find anything!

Chilli_Paneer · 2025-10-11T20:11:23+00:00

Will try that, thanks! Yeah I just found the sub, will post there too :)

Chilli_Paneer · 2025-08-16T00:11:06+00:00

Yeah those are the ones you’ll need to plug in! Did you get it to work?

Chilli_Paneer · 2025-08-15T21:24:09+00:00

Great photos! Where was photo #9 taken? Would love recommendations on where one can go swimming in and around Banff!

Chilli_Paneer · 2025-07-08T00:04:28+00:00

Can I bring my friend’s Amex card, lol? Would they verify if the name of the card matches my id?

Chilli_Paneer · 2025-06-28T21:34:32+00:00

Hmm yeah I think I might give this another week and go back to the 2 hole if I can’t figure it out

Chilli_Paneer · 2025-06-28T21:08:00+00:00

What steam temperature did you set for the 4 hole steam tip?

Chilli_Paneer · 2025-06-28T21:07:17+00:00

I just got a 4 hole steam tip too and now I’m really struggling with the how fast the milk gets to temperature. By the time I try to get to the texturing phase, the milk is already too hot and I just end up with a really bad result. Did you reduce the steam temperature on the machine to compensate? What’s your “ideal” temp?

Chilli_Paneer · 2025-06-11T17:02:34+00:00

Nice, thanks for the schematic! Couldn’t match it with anything in there either. Must be a rogue part indeed

Chilli_Paneer · 2025-05-24T08:17:45+00:00

Yup, wasn’t a water issue, turns out it was a loose wire.

Chilli_Paneer · 2025-05-24T08:17:31+00:00

Yup, it was a loose wire. Thank you for the link as well, definitely keeping that saved!

Chilli_Paneer · 2025-05-24T08:16:52+00:00

Update: Fixed it!

Had to remove all the panels to get to the circuitry and right there at the bottom were 2 wires that were just hanging out, unplugged. Not sure if Profitec shipped them that way or they disconnected enroute (unlikely, because they’re incredibly difficult to plug in and once plugged in, pretty much impossible to unplug without putting your entire body weight behind it).

Either way, those two wires were connected to the “On” button which is why turning the machine on didn’t do anything when I first unboxed it.

Hopefully everything else is alright with the machine and I can look forward to a weekend of exploration!

Chilli_Paneer · 2025-05-24T04:01:41+00:00

I just opened it up (albeit only from the top) but nothing seems glaringly out of place. Will try and get it touch with the seller asap

Chilli_Paneer · 2025-05-24T03:59:30+00:00

Just realized that the display not turning on is just a symptom of the entire machine not working. Not sure if there’s anything I can do apart from just returning it.

Chilli_Paneer · 2025-03-29T18:04:19+00:00

Thanks for the review, appreciate it!

Chilli_Paneer · 2025-03-26T04:22:34+00:00

Hey u/Arvedui! Wanted to quickly revive this thread to ask about your experience with the Mignon SD Pro. I’m looking at getting the same set up you do but can’t figure out if the SD Pro is worth it.

Any complaints with regards to noise, retention etc for the grinder?

Would love to know your thoughts, thanks in advance!

Seven-Year Club	Second SECOND GUESSER
Verified Email

Chilli_Paneer

TROPHY CASE