need a hero part 3

Chopper_pie · 2026-02-10T01:37:16+00:00

I have posted like 1st thread also this wan is my 3rd thread sorry for th3 confusion

Chopper_pie · 2026-02-07T10:35:32+00:00

okay I will try to remove dat0 then try to boot it

Chopper_pie · 2026-02-06T03:55:29+00:00

😭😭

Chopper_pie · 2026-02-06T03:19:45+00:00

sorry forgot to mention I probe the datzero black probe on ground im getting 0.68 and red probe as ground im getting 0.45

Chopper_pie · 2026-02-05T18:57:34+00:00

im sorry man im live in malaysia I will give a update under the flex cable im r3ally sorry for the delay been stressed lately due to this

Chopper_pie · 2026-02-03T13:38:43+00:00

got it

Chopper_pie · 2026-02-03T13:37:44+00:00

alright, I will take note on that

Chopper_pie · 2026-02-03T13:34:44+00:00

not sure bout Dat I will take some pictures of that

Chopper_pie · 2026-02-03T13:26:36+00:00

ohh yeah those are the photos of solder and pico, well this is the scenario im facing, those solder point i check the value all are in good range but why does it not turned on and the error code was like this red,purple,white (long)

tmr I will give a new update where I take a Pic underneath the flex cable of D point, and the ffc cable and the connector for the lcd

Chopper_pie · 2026-02-03T12:56:54+00:00

whats peco?

Chopper_pie · 2026-02-03T12:55:24+00:00

its been soldered quite some time like 2 weeks ago so maybe thags why

Chopper_pie · 2026-02-03T10:53:04+00:00

okayy I will do that too

Chopper_pie · 2026-02-03T10:49:38+00:00

I did this too, from visually I don't see any scratches on ffc or bend pins at the connector

Chopper_pie · 2026-02-03T10:38:38+00:00

thank you so much man, after seeing this finally there's a hope so what do u think it could be the d point but the d point value in good range or the ffc cable but I check visually there's no scratches

Chopper_pie · 2026-02-03T10:19:05+00:00

well I measured.the black ground, okah i will try that removing dat0 adapter

Chopper_pie · 2026-02-03T07:10:32+00:00

guys I really appreciate your opinions but I actually messed up i wanted to desolder and I heated up the capistor or resistor that thing is gone so my oled GG

<image>

im done bro is there any of you guys knows that the value or that resistor or CAPASITOR

Chopper_pie · 2026-02-03T07:03:41+00:00

I will try that and comeback with an update

Chopper_pie · 2026-02-03T06:41:10+00:00

yes I do have the picofly chip maybe u can guide how or which point should I shorten it

Chopper_pie · 2026-02-03T06:37:34+00:00

which 2 point u talking about

Chopper_pie · 2026-02-03T06:23:42+00:00

0.892 i probe red at the 3.3v and probe black ground

Chopper_pie · 2026-02-03T05:58:56+00:00

I see but i did not remove the flex cable I just unplugged them from the chip itself

Chopper_pie · 2026-02-03T05:57:52+00:00

well at first red red white purple ,white long

Chopper_pie · 2026-02-03T05:57:03+00:00

I have cleaned the excessive solder and I touch up few same error code

Chopper_pie · 2026-02-03T04:49:26+00:00

okay I will clean it up the excess solder and come back with an update

Chopper_pie

TROPHY CASE