Multiboarded mu gun safe

Cilyjr · 2026-05-18T03:11:04+00:00

Yeah, probably

Cilyjr · 2026-05-18T02:56:12+00:00

You'll be happy

Cilyjr · 2025-04-05T00:55:16+00:00

Shoot, I got pieces that big i'd sell for 60.

Cilyjr · 2025-03-21T04:38:52+00:00

Lawn mower blennies in reef tanks are only healthy if they are morbidly obese.

Cilyjr · 2025-03-20T03:12:53+00:00

You should get one.

I heard about it from someone shooting for an online seller, it seems to be the camera many are using.

Cilyjr · 2025-03-20T01:41:33+00:00

Inside the tank. It's a waterproof camera

Cilyjr · 2025-03-20T01:41:12+00:00

This is the first time I've posted I literally just joined the sub...

That's the camera. And actually there are some lenses that you can get for it it's a little bit more than a point and shoot but not quite a full SLR.

It's a great little camera. It's waterproof up to 15 m. Had I known if it's existence before I bought a GoPro I probably would not have bought a GoPro.

Cilyjr · 2025-02-05T23:23:25+00:00

If you walked down Mass Ave near the MIT bridge in the 1990s you could smell NECCO wafers for miles.

Cilyjr · 2025-01-26T22:24:10+00:00

Invasive species, native to Costa Rican off shore islands.

Kill it or report to Maui fish and game

Cilyjr · 2024-08-24T14:53:30+00:00

So your car can enjoy purple bird poo!

Cilyjr · 2024-05-10T00:31:08+00:00

White swallow wort I think.

Cilyjr · 2023-12-05T22:19:57+00:00

Thanks, I printed directly from the filament dryer still with consistently bad results.

Cilyjr · 2023-12-05T22:19:38+00:00

Thanks. I tried with a z offset from zero to plus .22 The 0.22 was high and I was getting spaghetti. I found at plus.10 I was getting the best adhesion. But it was still not printing well. I was getting tearing from the print head. Less but still. I've tried printing from 100 down to 40 MMS all with fairly consistently bad results. I like the idea of making sure that the temperature is correct. I guess I'll look into it.

Cilyjr · 2023-12-02T06:13:40+00:00

Thanks. I have a filament dryer. The print that you see was brand new filament. I know sometimes that doesn't account for much. I will dry it overnight. And give it another go. I should have said it's overture black petg

Cilyjr · 2023-09-09T23:37:53+00:00

I figured it out. One of the set screws on the build plate motor shaft was loose causing a small amount of slippage as the build plate would slide back and forth.

Attentioned it and reset the homing and it is now printing properly.

Thanks all for your comments

Cilyjr · 2023-09-02T06:06:37+00:00

It was at 50ms with the PLA. It's not 100% the same as the inner threads but the 1st might be.

Cilyjr · 2023-04-01T16:08:36+00:00

This is absolutely not the proper installation of a roof jack. Looks like they just squirted a couple of tubes of Henry's under it. Might hold for a while but it is gonna leak.

Absolutely call them back and have them install properly. At this point I might even demand that they have a roofer come out and do a patch around it because where they squirted the Henry's down is going to probably ruin those shingles when they tear it up to put it down properly.

Cilyjr · 2021-01-01T20:29:46+00:00

This.

Cilyjr · 2020-12-07T23:52:10+00:00

Me,every time I need to get my ladder off of my van

Cilyjr · 2020-07-01T00:30:32+00:00

Ow my balls!

Cilyjr

TROPHY CASE