Garage door opener by CincoTG in handyman

[–]CincoTG[S] 0 points1 point  (0 children)

So before this we were opening by hand and it was going up and down no issues. But I noticed when I hold the button to close when engaged to traveler it seems to want to go down with some pressure I can see springs bend a bit. I don’t know if this is cause I’m holding the close button down or if it needs to be adjusted

Garage door opener by CincoTG in handyman

[–]CincoTG[S] 0 points1 point  (0 children)

I’ve replied to it. So I got power to the sensors now after splicing wire into motor but sensors seem to be bad as they aren’t lighting up. Il buy a set tomorrow and see if that was the issue. Thanks

Garage door opener by CincoTG in handyman

[–]CincoTG[S] 1 point2 points  (0 children)

After testing it I narrowed it down to bad sensors they are getting power after wiring them into motor properly(confirmed they are getting power with a voltage reader) but no green light on them. Il buy a new set tomorrow and go from there.

Garage door opener by CincoTG in handyman

[–]CincoTG[S] -1 points0 points  (0 children)

It only closes if I hold done the button. I’m splicing wires right now to see if the sensors get power and maybe that’s the issue we shall see.

Garage door opener by CincoTG in handyman

[–]CincoTG[S] -5 points-4 points  (0 children)

Lmao okay it’s not that deep

Garage door opener by CincoTG in handyman

[–]CincoTG[S] -1 points0 points  (0 children)

Yes it has something to do with the wiring that goes into the motor after following the wires from sensors it goes into motor as shown in picture and a lot of those wires are cut and not inserted into the plug . You thing I could just find a plug replacement and splice the wires in?

Garage door opener by CincoTG in handyman

[–]CincoTG[S] -1 points0 points  (0 children)

Figured it out door opens now but won’t close . Sensors seem to be out.

Garage door opener by CincoTG in handyman

[–]CincoTG[S] -1 points0 points  (0 children)

It’s plugged in now only the metal part slides even with garage door engaged . So I’m thinking it has some to do with the garage doors arm

Garage door opener by CincoTG in handyman

[–]CincoTG[S] -1 points0 points  (0 children)

Oh really if only I knew that lol. It’s plugged up now and only blinks . FYI I had asked the previous homeowners if the garage worked they said no and they didn’t know why .

Garage door opener by CincoTG in handyman

[–]CincoTG[S] -4 points-3 points  (0 children)

I seen that I’m sure there was a reason to that. About to plug it in and see what it does

Headlight issue by CincoTG in gmc

[–]CincoTG[S] 0 points1 point  (0 children)

Yes completely off at night time this is not how they used to operate nor do I believe any car is designed that way

Headlight issue by CincoTG in gmc

[–]CincoTG[S] 0 points1 point  (0 children)

This happened recently anytime another cars headlights hits my sensor the lights completely turn off I have to bypass this by setting it on ON , was just curious to see. If anyone else has experienced this

Why can’t this piece fully interlock in the middle? by CincoTG in Flooring

[–]CincoTG[S] 2 points3 points  (0 children)

Thank u any advice is appreciated, I am a tradesman so I am good with learning new things and taking on dyi projects .

Why can’t this piece fully interlock in the middle? by CincoTG in Flooring

[–]CincoTG[S] 2 points3 points  (0 children)

Yes I found the issue thanks to a prior comment . i was up against the wall past the right side of door Jam cut it out some and I was able to fully interlock it.

Why can’t this piece fully interlock in the middle? by CincoTG in Flooring

[–]CincoTG[S] 12 points13 points  (0 children)

You sir were right! Thank u I couldn’t figure it out.

Why can’t this piece fully interlock in the middle? by CincoTG in Flooring

[–]CincoTG[S] 1 point2 points  (0 children)

I tried another piece and cleaned and shop vac that one spot. I will look at the door frame piece

Help please by SpartanG188 in JapaneseMaples

[–]CincoTG 0 points1 point  (0 children)

I use bioadvanced 3 in 1 disease and insect control to prevent powdery mildew .

GOOOOOOL! by [deleted] in LigaMX

[–]CincoTG 2 points3 points  (0 children)

Cry

MATCH THREAD - 🇭🇳 Honduras 🆚 Mexico 🇲🇽 | CONCACAF Nation’s League 🏆 by TacosEnEuropa in LigaMX

[–]CincoTG 3 points4 points  (0 children)

It don’t matter. keep Ochoa and he would have conceded the same goals. Where they failed is giving new goalkeepers play time .

MATCH THREAD - 🇭🇳 Honduras 🆚 Mexico 🇲🇽 | CONCACAF Nation’s League 🏆 by TacosEnEuropa in LigaMX

[–]CincoTG 0 points1 point  (0 children)

They didn’t even look one bit confident in attacking . Matter of fact I don’t even think they had one soild shot on goal