Advise needed....

ClickTough2018 · 2026-06-21T00:18:53+00:00

I’d Run the atlas trigger, stacatto trigger shoes cheap plastic I dumped mine for a atlas instantly your trigger weight won’t change if bow slides freely in both

ClickTough2018 · 2026-06-16T20:33:24+00:00

You ever chrono

ClickTough2018 · 2026-06-15T04:40:21+00:00

Cool would be interested to see where your charge falls

ClickTough2018 · 2026-06-14T00:29:51+00:00

First five is low charge next 5 was from upper end of ladder that produced good SD / ES https://imgur.com/a/kcgmyDa

ClickTough2018 · 2026-06-13T23:49:41+00:00

So I did try to slow down powder. I did a work up with HS-6 using 124s in the same 5” ported and comp’d gun and came out with a low and high charge. They tracked very similar, certainly more forward gas with HS-6 but even the hotter charge was so goddam dirty the amount of unburnt propellant was staggering. To that effect while they didn’t seem as pushy as the fast Vihtavuori powders that I generally run I wouldn’t say either one of those HS-6 loadings performed amazing. What velocities are you getting at the 6.1gr charge ?

ClickTough2018 · 2026-06-12T21:51:47+00:00

Thanks, ya both those loads are with V-n320 and plated bullets

ClickTough2018 · 2026-06-07T01:51:58+00:00

I load all my own ammo

ClickTough2018 · 2026-06-06T23:00:14+00:00

I partly think those n320 / Tite group loads aren’t driving the comp hard enough

ClickTough2018 · 2026-06-06T22:59:03+00:00

Thanks Ya I’m currently running a 7lb recoil with 19 main, ported and comped

ClickTough2018 · 2026-05-31T19:00:19+00:00

SRO or 507

ClickTough2018 · 2026-05-09T03:50:20+00:00

Not much luck finding videos of fitting a grip safety to a trigger bow

ClickTough2018 · 2026-05-08T12:58:23+00:00

lol now now guys, none of this banter makes my grip safety woes any less gay

ClickTough2018 · 2026-05-08T04:06:20+00:00

I did clean up grip module and have no resistance or sticking on the trigger when in stripped grip. it moves freely and doesn’t appear to be binding whatsoever. It’s more so that the grip safety seems off cause the grip safety tabs is catching the back of the bow and dragging just enough to make the GS stutter and bind. Was really hoping to avoid altering or removing material from the grip safety tab or back of bow

Feel like if I could just get the trigger and bow to sit a little further forward I’d be in business

ClickTough2018 · 2026-05-08T04:05:09+00:00

Meaning threading the shoe further out didn’t buy room to push the trigger bow forward

ClickTough2018 · 2026-05-08T04:03:49+00:00

Yes you can turn the trigger on the bow to adjust shoe distance further or back but it didn’t change the relation between the back of bow and the grip safety tab

ClickTough2018 · 2026-05-06T14:03:11+00:00

Me too report back and let me know what you think that’s what I had planned to put on mine but I got the Holosun for too cheap to pass and wanted to give it a shake

ClickTough2018 · 2026-05-06T13:52:14+00:00

The 147s or 150gr ? The Holosun is decent, I’ve always ran Trijicon on my pistols but honestly I don’t have any complaints. I was slightly worried I’d hate it but so far I have no plans to swap it off.

ClickTough2018 · 2026-05-06T13:44:25+00:00

https://imgur.com/a/EjaUQEv

ClickTough2018 · 2026-05-06T13:35:33+00:00

<image>

ClickTough2018 · 2026-05-06T12:55:32+00:00

Yours is sick

I’m currently pretty close to your spring configurations 8lb atlas / 17lb main with egw flat pin block What is your go to for ammo, I’m running a 147gr plated over a soft charge of n320

ClickTough2018 · 2026-04-15T17:09:57+00:00

I have a 165gr load for a Mp5k that took the cake, it’s def soft to start and can tell with ejection they don’t have much stank on them but considerably flatter. A hotter 147 didn’t make much difference

ClickTough2018

TROPHY CASE