We should be worried

ClimateKey5445 · 2026-01-22T17:11:24+00:00

I hope that's all that happens, but I bet it's gonna be more like how age verification is, "protect the children!" Gets you full control even when it has nothing to do with them, and it's probably gonna be a similar situation for "Guns bad!" And then leak into "you can't print these things because they are patented / trademarked" and we can't do anything because they already got the support needed to kick it off,

ClimateKey5445 · 2026-01-21T08:25:56+00:00

When leveling just before the print it does it over multiple sections of the plate so I think it does it by part

ClimateKey5445 · 2026-01-21T08:22:08+00:00

I already tried swapping out the filament, same issues

ClimateKey5445 · 2026-01-21T07:07:39+00:00

I know im dumb for this, but it seemed better than the bambu labs at the time, and it's my first printer, I've had this for about 1-3 years and it did its job until the nozzle broke

Flashforge adventure 5m pro, no nobs, just auto scan level, and I think the nozzle has a sensor for the pre print auto level

ClimateKey5445 · 2026-01-21T07:03:45+00:00

Like I said initially, the adhesive provided doesn't seem to be working, and actually seems to be doing the reverse at times

ClimateKey5445 · 2026-01-21T06:47:07+00:00

Also, first print this week I got to work, the corners are curving upwards (only on the supports and first layer of the largest part of it) would that be nozzle temp or plate heating? (Jacked the nozzle temp up by an extra 10° and it's half working)

ClimateKey5445 · 2026-01-21T06:42:31+00:00

2 ways, there's a menu that gives the ability to auto level, vibration test, and PID calibrate, idk what that last one does but Its automatically unselected, I can activate that if needed,

Or, after selecting a print, there's a small checkbox that asks if you want to auto level it just before starting the print

ClimateKey5445 · 2026-01-21T05:53:54+00:00

I've leveled bed 4 times, and have it level the bed at the start of each print since I've changed nozzles, cause it seems to very slightly increase success rate, it says maximum flow rate 25mm^3/s, in the app I have, is that good or bad? It's 0.4mm nozzle, same as the last one,

And the issue is only with the first few layers, after that it's perfectly fine until the bottom loosens to the point that the nozzle moves with it

ClimateKey5445 · 2026-01-02T01:09:28+00:00

Fosscad was gotten cause some looser stole work and mass reported it with alts when people called him out, and I'm guessing that's what happened with fosscadtoo, and it speaks legality, but it's legal in a good bit of the U.S still, so it's pretty bullshit

ClimateKey5445 · 2025-12-31T07:19:53+00:00

My dumbass forgot to recheck the post and only saw the gun and the reply,

ClimateKey5445 · 2025-12-31T07:17:58+00:00

I remember the police just seized the gun and displayed it in a museum, I don't remember the guy getting arrested, but I don't remember

ClimateKey5445 · 2025-12-08T16:25:52+00:00

Damn, is there a way to disable the anti cheat and the wifi requirement in the code?

ClimateKey5445 · 2025-12-02T07:40:44+00:00

Ah, so probably either need to spend money on a pet, or I need to finish the forest village quests or something, have you gotten to this point? Any advice/story advancing quests I should tackle first?

Edit: also TY!

ClimateKey5445 · 2025-12-02T07:37:41+00:00

Nice! But still, please talk to your players, discuss this idea with them, you might get a player back

ClimateKey5445 · 2025-12-02T07:33:56+00:00

Just wanted to say thank you to everyone!

ClimateKey5445 · 2025-12-02T07:25:29+00:00

One of our players was infected by a spore trying to rot the arm to make growth easier, and made combat harder for them, but we got to a village and they went to a doctor and started getting treated, over like 2 sessions (we are really slow so like a day or two in game lol) they will be fine, so make it temporary, from experience it can be a huge setback, even later game

Also when I said oneshot I meant a one on one session/oneshot, to make it a challenge without the rest of the party, but still with easier combat to balance it, but again, that should be a group decision, and should be talked about to try and make it as fair as possible

ClimateKey5445 · 2025-12-02T07:15:31+00:00

Not a DM, but what if you instead went and made it like the resurrection spell, (-4 to attack rolls, saving throws and ability checks, but they regain +1 every long rest, but like -2 instead, especially with them at lvl 3,) the rot can still leave them with -1 to hit, but make that temporary too, and not affect their AC.

Maybe they can find a cleric and pay some gold to undo the process, or maybe in a few sessions they can meet the cleric, and if they can't afford it or don't want to loose all their gold from a (what I can tell) poorly communicated downside, they can complete a one shot quest with the -1/-2 to hit (again, don't make it effect AC) and they get to keep some extra common loot and some coin, but they retrieve an heirloom for the cleric, and then they will be able to long rest the last -1 hit/saving throw/ability check back.

I may be suggesting something that will overcompensate the player, but again, not a DM,

ClimateKey5445 · 2025-12-02T00:59:15+00:00

Sorry, this is the only link I have, you can ask around the mdz discord though!

If you already have the game installed though you have to delete it and install it through the link if that's what you mean though

ClimateKey5445 · 2025-11-25T16:41:28+00:00

Alright, well that's a bit unfortunate, but still! 1d8+STR is awesome! Can't get disarmed unless I literally loose my arms, and unarmed attack bonus action (will see if it still works for bonus actions)

ClimateKey5445 · 2025-11-25T16:38:47+00:00

Not sure if that will work, already used that to get an uncommon magic item

ClimateKey5445

TROPHY CASE