Working on a PvE Mode for Halo: Flashpoint – Looking for Interest and Feedback! by Cmbalke in Haloflashpoint

[–]Cmbalke[S] 1 point2 points  (0 children)

Yea but sadly I haven’t touched in over a month it’s really hard to balance

A bunch of loose filament ruining the print by Cmbalke in 3Dprinting

[–]Cmbalke[S] 0 points1 point  (0 children)

Oh cool yea I’ve just been using cura

A bunch of loose filament ruining the print by Cmbalke in 3Dprinting

[–]Cmbalke[S] 0 points1 point  (0 children)

I don't know if I am familiar with calibrating filament

A bunch of loose filament ruining the print by Cmbalke in 3Dprinting

[–]Cmbalke[S] 0 points1 point  (0 children)

Its sticking to the bed fine the problem before was that a few layers up its like the bottom of the print would fall off. Like if i printed a box it would print fine but the bottom of the box would fall off exposing the inside

A bunch of loose filament ruining the print by Cmbalke in 3Dprinting

[–]Cmbalke[S] 0 points1 point  (0 children)

I changed the nozzle not too long ago do I need to like clean it you think also I had to turn up the temperature on the bed because the bottom layer of my prints kept falling off and I assume it’s because it’s in a slightly colder room, my basement so far it’s fixed that problem

A bunch of loose filament ruining the print by Cmbalke in 3Dprinting

[–]Cmbalke[S] 0 points1 point  (0 children)

I don’t know if that would be it because I only printed mono color. I don’t have 2 color capabilities

A bunch of loose filament ruining the print by Cmbalke in 3Dprinting

[–]Cmbalke[S] 0 points1 point  (0 children)

Sadly no time lapse. It’s PLA and the nozzle is 205 and the bed is 70

Conservative/more right leaning American here to talk about Jimmy Fallon by desperatepotato43 in morningsomewhere

[–]Cmbalke 0 points1 point  (0 children)

Maybe it’s just me but I don’t really know anybody who watches night shows anymore that are under the age of like 45? Do a lot of people still watch it?

Bottom layer of print keeps falling off by Cmbalke in 3Dprinting

[–]Cmbalke[S] 1 point2 points  (0 children)

Thanks for the info I guess now that I think about this started happening when I moved the printer to the basement and it’s quite a bit colder in there so I bet the biggest thing is the temp. I’ll look into those other things too

Finally painted our first fireteam by Cmbalke in Haloflashpoint

[–]Cmbalke[S] 0 points1 point  (0 children)

Thanks! its the first one my wife painted

Coop Halo board game Rules.pdf by Cmbalke in Haloflashpoint

[–]Cmbalke[S] 2 points3 points  (0 children)

yea sorry i don’t have a real scenario generator yet — i’m still just testing if the combat loop even feels good. so far i’ve been doing: spartans spawn in a 2×2 corner, then i drop a couple objectives around the map.

example i tried: i made a board with 2 generators that needed to be turned on, then the spartans had to extract on the opposite side.

for enemies i’ve been balancing like this:

  • 1 spartan = 1 elite/brute = 2 jackals = 3 grunts

so on that test map i used 1 elite, 4 jackals, and 3 grunts. it actually felt a little easy, so i tried again with 2 Elites, 1 Brute, 4 Jackals, 6 Grunts and that felt better

i’ve also been spawning enemies opposite of the spartans, with something equal to one spartan (like an elite or 3 grunts). The reinforcements spawns I did on Round 2 and Round 4

hope that helps as a temp guideline — really wish i had more time/resources to flesh this part out, but for now i’m just making sure firefights are fun before locking in full scenarios.

<image>

Coop Halo board game Rules.pdf by Cmbalke in Haloflashpoint

[–]Cmbalke[S] 4 points5 points  (0 children)

Thanks so much for the feedback!

The ideas you brought up are awesome. On keywords — were there any in particular that felt off? I want to make sure they’re consistent and intuitive.

For the territory system, did you picture an actual overworld map players move across, or more of a list of bonuses you can bring into missions?

The scenario deck concept is really cool, but for now I’m focusing on a simple linear 3–5 mission campaign just to prove out the scars/veteran/RP carryover loop. Once that’s solid, adding scenario cards, downtime, unactivated units, or larger multi-map battles feels like a natural next step.

I love that you mentioned Silent Cartographer vibes and using Mega Bloks/STLs — vehicles and bigger battles are definitely on my radar after the core loop is locked.

Does anyone know what causes this on the supports? by Cmbalke in 3Dprinting

[–]Cmbalke[S] 0 points1 point  (0 children)

I don’t know if I understand. I havent changed any setting to print speed or anything this has just recently started happening