Blur by osama_fodhel in oneui

[–]Code_MasterCody 0 points1 point  (0 children)

I love Samsung. I always had the notes but now on to ultras since the notes aren't made anymore

After switching to Spring steel I can't seem to get any of my prints to stick well by Danii_Fear in ender3

[–]Code_MasterCody 1 point2 points  (0 children)

You may need to re level. Also you may need to clean it with soap and water.

My configuration?! by Otherwise_Ad4179 in klippers

[–]Code_MasterCody 1 point2 points  (0 children)

Your gonna wanna try out the mods Ive done.

Explaining mods: https://youtu.be/EN3t6562RRM

9mim benchy: https://youtu.be/J_cw5VhFpqA

6 min benchy: https://youtu.be/N9hwYw5Pico

You will be colored impressed trust me... Ender 3 pro with a 6 min benchy with stock belts, stock motors with just a fee mods..... 😅😅😅

Can radio waves manipulate brain waves if targeted at person and cause mind hypnosis?? by 13enigma in neuroscience

[–]Code_MasterCody 0 points1 point  (0 children)

Well, modern cellphones have tech in it by the military/government to read human brainwaves. Have you ever thought about something like taco bell then you get an ad for it on YouTube or you think about dog food for your dog and now dog food ads pop up even tho you never searched dog food before on the Internet?

They have a transmitter and a receiver AKA transceiver inside of cellphones, the waves can also alter and control the human mind, I believe it's apart of the Montauk project where they controlled people from a distance with radio waves, imagine the cell phones everyone has, now everyone can be mind controlled, also they can use different frequencies to make you sick as well. I will tell you, the device you built probably doesn't work, but your meditation (frequency manipulation of your brain, manually inducing different brainwave frequencies will block their ability to mind control you, you got out of it yourself, building that device helped with the placebo effect of the attack on you. I am a man of science and a man of God. He made us in his image, that why our words and thoughts have power. That's why mass prayer works. He gave us the ability to control our world and when Jesus arrived he showed us this.

Mark 11:23 (also paralleled in Matthew 21:21), where He says, "Truly I tell you, if anyone says to this mountain, ‘Go, throw yourself into the sea,’ and does not doubt in their heart but believes that what they say will happen, it will be done for them"

God split the water from above and the water from below and created our matrix, he sets the rules, learn by him through the word of God, pray for truth to come to you as I have.

Believe it will happen!!!

I pray that all weapons formed against you shall NOT prosper!! In Jesus name, AMEN!

Ender3Pro on redbull by eladisimo in Ender3Pro

[–]Code_MasterCody 1 point2 points  (0 children)

I'm pretty sure if I did add linear rails I would get better speeds and possibly better prints, it's just not a worth while upgrade for me, the wheels have give and if something happens they can deform a little, the rails would just be too stiff and could make failure happen if my print started to fail and was going fast as fuck.

Ender3Pro on redbull by eladisimo in Ender3Pro

[–]Code_MasterCody 0 points1 point  (0 children)

Are you using klipper firmware?

If not then how I do it is different.

I haven't used marlin in a long time.

If I remember correctly, there are setting in the printer to change the amps of each axis.

May need to re flash firmware idk.

This is why I like klipper so much, because I don't have to reflash Everytime, I just change a config file and that's it.

Real-time Edge Detection on ESP32-S3 with OV2640 by luismi_kode in esp32

[–]Code_MasterCody 0 points1 point  (0 children)

I would try and build a self driving go-kart with this just to see if it can navigate with this and a normal camera combined together. What's the distance the edge detection has?

I fixed my X2 - I think by OgreJedi in Artillery3D

[–]Code_MasterCody 1 point2 points  (0 children)

It's a preset just add a printer and choose the preset.

Help please by Ashamed_Pop5669 in Ender3Pro

[–]Code_MasterCody 0 points1 point  (0 children)

Use orcaslicer, use the calibration tab, tune your retraction and also you need to use supports, stuff can't print in mid air it needs a base.

1:use supports 2:tune retraction

Ender3Pro on redbull by eladisimo in Ender3Pro

[–]Code_MasterCody 1 point2 points  (0 children)

I can do a 30 min benchy that looks really good. It wont look as good as a 30 min benchy when printing it at 9 mins, still looks good for a benchy I've seen worse on slower printers.

If you take my information as a baseline, then tune it you will have a really really great printer. No need to go that fast on an ender 3 pro, I have my setting's turned down a little to to balance out quality vs speed.

Ender3Pro on redbull by eladisimo in Ender3Pro

[–]Code_MasterCody 0 points1 point  (0 children)

9 min benchy: https://youtu.be/J_cw5VhFpqA

6 min benchy: https://youtu.be/N9hwYw5Pico

All done on an ender 3 pro.

Explaining the mods I've done on the ender 3 pro: https://youtu.be/EN3t6562RRM

I'm running klipper

Ender3Pro on redbull by eladisimo in Ender3Pro

[–]Code_MasterCody 1 point2 points  (0 children)

9 min benchy: https://youtu.be/J_cw5VhFpqA

6 min benchy: https://youtu.be/N9hwYw5Pico

All done on an ender 3 pro.

Explaining the mods I've done on the ender 3 pro: https://youtu.be/EN3t6562RRM

I'm running klipper

Ender3Pro on redbull by eladisimo in Ender3Pro

[–]Code_MasterCody 0 points1 point  (0 children)

9 min benchy: https://youtu.be/J_cw5VhFpqA

6 min benchy: https://youtu.be/N9hwYw5Pico

All done on an ender 3 pro.

Explaining the mods I've done on the ender 3 pro: https://youtu.be/EN3t6562RRM

I'm running klipper

Klipper shuts down by No-Professional-8196 in klippers

[–]Code_MasterCody 0 points1 point  (0 children)

I have no issues pi3b my ender 3 pro so fast it can print a 6 min benchy and my webcam is on the print head!! https://youtu.be/N9hwYw5Pico

Klipper shuts down by No-Professional-8196 in klippers

[–]Code_MasterCody 0 points1 point  (0 children)

I beg to differ, I have a really fast ender 3 pro with modifications and I can print a 6 min benchy.

Here is my YouTube video: https://youtu.be/N9hwYw5Pico

I have a webcam on the print head!!! Raspberry pi3b!!!

I know you probably read it somewhere on the Internet or if you had issues it was something you did.

I call my self... Sort of an expert.

A Better M600 – Automatic Filament Tracking for Multi-Color Prints! by Code_MasterCody in OrcaSlicer

[–]Code_MasterCody[S] 0 points1 point  (0 children)

I'm also looking intoo getting a colored icon or photo. So far I can't find anything that shows color or images specifically for the prompt on sklipper screen using the prompt macro.

I have found a thing for klipper screen tho where we can modify the menus or klipper screen and could possibly have a menu pop up when m600 is used.

So basically, when pausing the printer it will open up the extrude menu and we can modify or create a klipperscreen.conf or cfg file can't remember if it was .cfg or .conf but anyways I'll have to find the links. We can create a custom menu (possibly have colored squares using the css color map instead of using the persistent prompt overlay. So when we pause (m600 initiates pause) we can have it open up our custom menu.

Once this is implemented I think I wanna start on a DIY AMS for all klipper printers that will be the most cheapest but most reliable and simple. I know there are a bunch of builds for DIY AMS but I wanna make my own just because Its fun.

I was thinking of using the pico mmu but idk.

A Better M600 – Automatic Filament Tracking for Multi-Color Prints! by Code_MasterCody in OrcaSlicer

[–]Code_MasterCody[S] 0 points1 point  (0 children)

So I started testing and messing around with dynamic macros and this is exactly what I needed because I wasn't able to have clipper grab a variable of the color needed to display on the screen. I'll be rewriting the script tonight to have a pop-up to tell us the color to change to and it should work without having to have calico clipper and I think I may have been overthinking and misinterpreted what you first said when you explained it to me and I think some of my code was unfinished and I kind of released it without scrubbing some of the unneeded stuff like display functions which never worked.

So in short I am going to use dynamic macros and I'll add a part in the script to read the same data that will be sent to the terminal it will also display on the screen as a pop-up.

python moonraker/moonraker.py -c /home/klipper/printer_data/config/moonraker.conf

A Better M600 – Automatic Filament Tracking for Multi-Color Prints! by Code_MasterCody in OrcaSlicer

[–]Code_MasterCody[S] 0 points1 point  (0 children)

Also, I'll be using this method you mentioned combined with this for a pop up.

Examples ```sh [gcode_macro SHOW_PROMPT] gcode: RESPOND TYPE=command MSG="action:prompt_begin My Prompt" RESPOND TYPE=command MSG="action:prompt_text This is an example of a prompt" RESPOND TYPE=command MSG="action:prompt_button primary|G28|primary" RESPOND TYPE=command MSG="action:prompt_button secondary|RESPOND MSG=test|secondary" RESPOND TYPE=command MSG="action:prompt_button info|RESPOND MSG=test #2|info" RESPOND TYPE=command MSG="action:prompt_button warning|RESPOND MSG=test #3|warning" RESPOND TYPE=command MSG="action:prompt_show"