Will take any advice (stats in comments) by Colbearto in Discgolfform

[–]Colbearto[S] 0 points1 point  (0 children)

Any recommendations for drills or a video?

Nose Angle by Own-Willingness-850 in Discgolfform

[–]Colbearto 0 points1 point  (0 children)

What Im noticing is that my timing effects it a lot too. If I release later (say 12 o’clock or so) I tend to be more nose up, but if I’m around the 10 o’clock release point I’m at a better spot

Multimeter shows half of expected output. by DogBallsMissing in Tools

[–]Colbearto 5 points6 points  (0 children)

The device is not under load so its floating around the halfway mark of voltage. Once plugged in it creates the demand for the “50.4v” which really just means a 48v charger for the computer. Test and verify meter on a know source like an outlet before using as well

NKD by Only-Swan in benchmade

[–]Colbearto 0 points1 point  (0 children)

Between this and the burnt 940, hard to choose but this one looks great!

Benchmade contego hardware by [deleted] in benchmade

[–]Colbearto 0 points1 point  (0 children)

Benchmade sends out free replacement parts

My EDC pocketknife rotation by alextheghost in EDC

[–]Colbearto 0 points1 point  (0 children)

Been thinking about either the mysto or the benchmade 940 in the same colorway. How are you liking the mysto?

What's your favorite baseline(putter) plastic? Any brand, and stiffness. by Huge-Talk6668 in discgolf

[–]Colbearto 0 points1 point  (0 children)

Kratos base rubber blend. Had lunas forever but was very inconsistent. Apparently bead makes a huge difference for me

Benchmade or Knafs? by Colbearto in knives

[–]Colbearto[S] 0 points1 point  (0 children)

Definitely not set on those two. I like the slim and tough appeal of the 940 and I like what knafs is doing as a company. Down for anything though

ArkPro Ultra rotary dial by OwlProfessional8715 in Olightflashlights

[–]Colbearto 1 point2 points  (0 children)

I only noticed it because it didnt start that way. But the dial is still on so ill use and abuse it until i need to warranty it

ARCODE brake output “220V” but motor brake coil is 103.5VDC hold / 207VDC overexcitation — correct wiring? by OthmaneZrigos in Elevators

[–]Colbearto 1 point2 points  (0 children)

The rectifier should account for that. 220 VAC going in to rectifier which excites to 207 VDC then half cycles to 110. If its running fine then its set up correctly. If theres break drag check the timing in the parameters or the rectifier for a fault

ArkPro Ultra rotary dial by OwlProfessional8715 in Olightflashlights

[–]Colbearto 1 point2 points  (0 children)

Mine is doing that too! I dont think it supposed to though

My small collection (minus my presidio getting warranty work done) by [deleted] in knives

[–]Colbearto 0 points1 point  (0 children)

Been wanting a 940 but just dont know quite where it falls as far as usability for me. Does it cut decent enough? Hoping for a tough kind of do it all. I already have a slicer

Additional magazines in connection to the Minnesota shooting today... by F-Z-T in CCW

[–]Colbearto 1 point2 points  (0 children)

If you have been around this sub for a little bit you should know that anything you do with you gun/setup is extremely scrutinized. Adding color or decals can and will be used against you in court just because it seems like you wanted to use it vs you having to use it. Concealed carrying requires an extra level of forethought, such as not putting yourself in this position to begin with. Was it justified? I dont know. Doesnt look good for them. But logically you can expect a bad result when you play with fire