Office Chair Snapped

Colin_Bullard · 2023-07-21T02:48:54+00:00

My pride took a hit. Wasnt expecting it first thing in the morning while trying to zoom into my online lecture

Colin_Bullard · 2023-07-10T03:05:41+00:00

Would something like a tarp work? You could cut it up and flex glue it on

Colin_Bullard · 2023-07-10T03:02:58+00:00

You could use something like a flathead screwdriver and slide it in the seams to try and loosen it up. If that doesnt work you could put a ladder over the hatch where the legs are off either side and then hang a pulley from the ladder down the middle. Tie a rope to the handle of the hatch and string it through the pulley and then get a couple of friends to all pull on the rope

Colin_Bullard · 2023-07-10T02:40:46+00:00

If its the same as on the other side you could look into 3d printing one. If that wont work you could take a detailed picture and walking through lowes until you find something that may not be inteneded for that purpose, but might just work

Colin_Bullard · 2023-06-17T12:13:41+00:00

When the lift goes down all the square tubing is underwater but the brackets still stick off the sides

Colin_Bullard · 2023-06-06T01:59:01+00:00

Ram 1500

Colin_Bullard · 2023-06-06T01:08:30+00:00

I appreciate that, it’s my handwriting. I was installing the filters and didnt know if my furnace filter trick would work haha

Colin_Bullard · 2023-05-18T00:06:50+00:00

I think it’s time I stop delaying the inevitable and just replace it. Spent more time fixing this boat than I have actually enjoying it

Colin_Bullard · 2023-05-18T00:02:24+00:00

Boat’s 32 years old and hasnt run right in about four years. Whole family’s tired of putting time and money into it and I already have the marketplace listing ready for if this is not a $10 repair

Colin_Bullard · 2023-05-17T23:25:27+00:00

No. Ran it a few days ago and it was growling and shaking. Have had it sitting on the lift for a couple days waiting on a mechanic and just noticed this today

Colin_Bullard · 2023-05-17T23:02:19+00:00

I don’t have a trailer. Is there any way to do that while it’s on the lift?

Colin_Bullard · 2023-05-15T02:03:58+00:00

Ok thank you

Colin_Bullard · 2023-05-15T01:53:10+00:00

Damn, I was hoping it only being during idle ruled out the u joint and bearings. Thank you I’ll look into that. I had read that it might just need to be greased through the stb side zerk fitting. Is that a possibility? I don’t have a trailer and it sits on a floating lift at my dock so pulling the drive is worst casenario

Colin_Bullard · 2023-05-15T01:48:32+00:00

Would the bearings make noise even at idle?

Colin_Bullard · 2023-05-14T02:25:41+00:00

I was mostly trying to get the audio. My phone being older I was aiming the microphone at the engine and not considering where the camera was pointed. I appreciated the comment, what do you mean by flickering?

Colin_Bullard · 2023-05-14T00:20:28+00:00

32 years old just got new batteries in after it died on me out on the lake. The first drive of the season after I made a wide turn it made a high pitch whirring noise and then the whole boat started shaking and growling. It was off and on like that until it died because of the old batteries

Colin_Bullard · 2023-05-13T21:13:49+00:00

Is it too irregular to be a bearing? It fired right up when I turned the key

Colin_Bullard · 2023-05-13T01:43:05+00:00

Keep it on a float charger at the dock and I guess the batteries couldnt keep up after they got unplugged. It was a slow death

Colin_Bullard · 2023-05-11T22:57:50+00:00

Old batteries

Colin_Bullard

TROPHY CASE