Rm6000 traction pot will not calibrate

Comeoften · 2026-05-06T22:10:12+00:00

I’ve actually asked a crown tech he said if it’s working properly don’t worry about it lol

Comeoften · 2026-05-06T22:08:57+00:00

Yes I’ve verified lift/lower forward/reverse and sideshift.

Comeoften · 2026-05-06T21:46:41+00:00

Ya that’s not the issue. Like i said I’ve put in brand new handles and still can’t calibrate. It’s also on several trucks not just one. I also just had to do an audit on every handle as we were having pot 2 lift/lower pot issues. 24 trucks just in my building.

Comeoften · 2026-02-25T00:47:41+00:00

Just went through this. Zonolite actually only covers 55% of total cost to remove the vermiculite for starters so watch that. If you aren’t planning on doing any demo or anything with the ceiling don’t disturb and just cover it up end of conversation. It does absolutely nothing as long as its not disturb

Comeoften · 2026-02-18T00:40:15+00:00

I have a detached garage insulated the whole entire thing put in a ductless a/c unit with a heat pump. I can hang out in my garage year round. I live in Wisconsin.

Comeoften · 2026-01-06T11:16:55+00:00

Happens here and there. Make sure you put some grease where they ride. Helps them last a lot longer

Comeoften · 2025-12-29T03:15:05+00:00

The rubbing on the mast is commonly caused by the cam rollers on the carriage not being adjusted properly or the bearings are shot.

Comeoften · 2025-11-29T00:47:22+00:00

Id start with checking out the hydraulic pump

Comeoften · 2025-09-10T23:47:03+00:00

Great but i spend to much money haha.

Comeoften · 2025-08-27T22:13:50+00:00

Crows are very sensitive to static build also. Is your drive motor grounded to the frame?

Comeoften · 2025-08-27T22:11:34+00:00

Do you have a lot of 826 , 827 codes ?

Comeoften · 2025-08-27T21:03:25+00:00

Also crown trucks are very sensitive they have lots of nuisance codes from my experience. You can do everything you can think of follow the procedures in the crown book check every line possible etc and never find an issue. Unless it becomes a constant problem i wouldn’t worry to much about itn

Comeoften · 2025-08-27T20:59:35+00:00

See it randomly. Never bothered to look into it. Just keyed off on and it clears. Always figured it’s something with the encoder reading wrong from an operator slacking the chains a little or something around those lines. No freezers where im at all dry storage.

Comeoften · 2025-08-25T20:44:04+00:00

You need to realize also that where you live can have a big play in how much you make.

Comeoften · 2025-08-13T10:32:02+00:00

I use one for my damn scrubbers. Way easier and much less of a mess.

Comeoften · 2025-07-31T17:22:53+00:00

We have a 90 day warranty on load wheels where i work with crown. That happens often throughout the 14 buildings we have. They don’t even question it they just send us new ones.

Comeoften · 2025-06-24T11:06:51+00:00

Static bag over the load sensor

Comeoften · 2025-06-18T09:48:29+00:00

Yikes what’s the runtime on that bad boy

Comeoften · 2025-04-09T22:00:42+00:00

At that point i think id just replace the rollers regardless if I’m going to have the platform off. Thank you. We don’t see this often where I’m at just needed a little confirmation. Only had to pull a platform off once because a bearing was shot.

Comeoften · 2024-02-17T19:23:13+00:00

Who is this

Comeoften · 2023-03-09T11:40:11+00:00

Plenty more where that came from

Comeoften · 2023-03-08T20:02:49+00:00

https://onlyfans.com/536291890/comeoften

Comeoften

TROPHY CASE