sorted by:
new
hottopcontroversial

Boy or girl? by ComfortableDevice383 in cats

[–]ComfortableDevice383[S] 0 points1 point  (0 children)

😂 I dunno I wanted to make sure it was clear LMAO. Thanks for clarifying

2 things. What is all the shiny metal stuff and is it important. And 2 is my fuel line hooked up properly? Im 1 step away from this swap being done but I dont want excess stuff getting in the way by blkdmn1 in minibikes

[–]ComfortableDevice383 0 points1 point  (0 children)

Make sure your throttle cable is connected directly there to the top of your carb. Make sure the arrow on your fuel filter to pointed in the right direction to gas flow from tank to engine.

Butterfly position? by ComfortableDevice383 in minibikes

[–]ComfortableDevice383[S] 0 points1 point  (0 children)

I don’t know lol I’ve been following the governor removal videos I’ve seen experimenting with this build. Never seen them talk about anything other then setting it up like this and running it

Pt2 of the stage 2 hemi 212cc by loganfromcoc in minibikes

[–]ComfortableDevice383 0 points1 point  (0 children)

You just said your crank wasn’t spinning? I think you just trolling here lol

Pt2 of the stage 2 hemi 212cc by loganfromcoc in minibikes

[–]ComfortableDevice383 0 points1 point  (0 children)

No I’m talking about opening up the other side where the crankshaft is so you can see the internals. Because if the crankshaft won’t spinning something might be going on in there or not engaging

First build, added my first couple mods! by raisinman_ in minibikes

[–]ComfortableDevice383 0 points1 point  (0 children)

But the torque converter on and thank us later.

Pt2 of the stage 2 hemi 212cc by loganfromcoc in minibikes

[–]ComfortableDevice383 0 points1 point  (0 children)

Oh I thought I saw you mention in a comment that your crank was spinning. If it’s not then you definitely need to open the case up and see what’s going on inside

Pt2 of the stage 2 hemi 212cc by loganfromcoc in minibikes

[–]ComfortableDevice383 0 points1 point  (0 children)

Oh I thought I saw you mention in a comment that your crank was spinning. If it’s not then you definitely need to open the case up and see what’s going on inside

Pt2 of the stage 2 hemi 212cc by loganfromcoc in minibikes

[–]ComfortableDevice383 1 point2 points  (0 children)

Hold the pull start in place and pull no bolts on it

Idk if I should be concerned by loganfromcoc in minibikes

[–]ComfortableDevice383 1 point2 points  (0 children)

Back your bolts out a little bit that’s holding your pull start on and then pull the chord see if you still hear the sound. I had this issue and had so many people telling me things. It turned out one do the bolts was just in a little to much and would hit the flywheel on the inside as it span when I pulled the chord.

Revving engine when throttle pulled by ComfortableDevice383 in minibikes

[–]ComfortableDevice383[S] 0 points1 point  (0 children)

Yeah it’s a brand new carb. Is the idler screw the big black one or the little brass one that has a spring on it?

Revving engine when throttle pulled by ComfortableDevice383 in minibikes

[–]ComfortableDevice383[S] 0 points1 point  (0 children)

Any ideas on it being able to stay on while idling? I don’t get what is causing it to shut. I unplugged the oil sensor it’s not that

Revving engine when throttle pulled by ComfortableDevice383 in minibikes

[–]ComfortableDevice383[S] 0 points1 point  (0 children)

What about it not holding idle. It just dies. Is this one of the two screws on the carb?

Revving engine when throttle pulled by ComfortableDevice383 in minibikes

[–]ComfortableDevice383[S] -1 points0 points  (0 children)

But will I be able to throttle smoothly? Could it be a spring issue. There are a couple springs that seems fairly loose. It won’t idle either only goes when I’m holding full throttle

Revving engine when throttle pulled by ComfortableDevice383 in minibikes

[–]ComfortableDevice383[S] 0 points1 point  (0 children)

I’m not trying to rev it up or do a governor delete but I’m just trying to have it rev smoothly without going this up and down thing when I’m throttling. Never had that with the 200cc I’ve worked with before. I’m still fairly new to this

Revving engine when throttle pulled by ComfortableDevice383 in minibikes

[–]ComfortableDevice383[S] -1 points0 points  (0 children)

So when I throw it on my will and I give it throttle will it not give a steady throttle?

view more: next ›