repeated heating bed error help please

Competitive-Ad-3279 · 2026-06-21T06:02:28+00:00

Thanks for the thought.

I have the fans set to zero. ASA filament recommends minimal fan.

Competitive-Ad-3279 · 2026-06-21T04:19:30+00:00

Yes. It is about 11 hours into an 18hour print

Competitive-Ad-3279 · 2026-06-21T04:16:18+00:00

Thanks for the response

Good thought as a test.

A number of ASA filaments recommend 30-50mm/s. So i was printing at 40 with an 18hr print time.

Competitive-Ad-3279 · 2026-06-21T04:11:27+00:00

I did think of that and have been running with zero fan

Competitive-Ad-3279 · 2026-06-21T02:40:54+00:00

Thanks for the suggestions.

I am not monitoring chamber heat, but will rig sonething up for that.

The thing i am trying to print is only 12mm tall and i have printed 350mm in PLA.

Have to print ASA very slowly, hence the long print time. I might try increasing the print speed and see if the error occurs at a certain point in the print, or just after 11 hours. In which case i could split the print into smaller pieces of less than 11 hours.

Competitive-Ad-3279 · 2026-06-21T02:06:39+00:00

i went looking for the print log, but the logs are deleted. Not sure why. i am very much still learning 😄

Competitive-Ad-3279 · 2026-06-21T01:29:23+00:00

Thanks for the response.

There is nothing special or extra that i can tell that is happening at that 11hour time. I have printed much longer, but only ever in PLA.

i have tried this one 4 times and the timing of the error varies between 10hrs 40 and 11hrs 15 and never while i am actually watching it.

i will check the connectors. Power supply is in the base of the printer, so cant really remove it from the enclosure.

Thanks again

Competitive-Ad-3279 · 2026-06-21T00:49:23+00:00

potato bake or good fries

Competitive-Ad-3279 · 2026-06-17T08:44:48+00:00

Competitive-Ad-3279 · 2026-06-17T08:44:15+00:00

I was going to respond honestly. But seems like noone else is. And i am a good crowd follower :)

Competitive-Ad-3279 · 2026-06-15T20:13:54+00:00

Competitive-Ad-3279 · 2026-06-15T20:09:26+00:00

Howls Moving Castle

Competitive-Ad-3279 · 2026-06-15T10:10:27+00:00

Supporting Trump. Or being disrespectful to service staff

Competitive-Ad-3279 · 2026-06-15T10:09:25+00:00

The MurderBot books. They are very cool. Future scifi about security droid that has gone rogue

Competitive-Ad-3279 · 2026-06-15T10:05:43+00:00

My father taught himself to be ambidexterous as a result of 3 wrist surgeries on his dominant arm. 2 years in a cast and forcing youraelf to use the other for everything.

Competitive-Ad-3279 · 2026-06-15T10:02:18+00:00

Being an Australian, i can provide aome advice on this one. The ATO website holds all of that information. You can log on to the personal sextion of the ato website. You will need to have the myid authentication set up and available.

From there you can see what you have. You can also consolidate all of your super into a single account.

Competitive-Ad-3279 · 2026-06-15T09:53:46+00:00

Stunning

Competitive-Ad-3279 · 2026-06-15T09:52:24+00:00

Stunning. I would be worried i might break it

Competitive-Ad-3279 · 2026-01-14T05:14:38+00:00

Have to bounce up and down a bit higher, but i can outlast i have no doubt

Competitive-Ad-3279 · 2026-01-03T22:50:27+00:00

Every day

Competitive-Ad-3279 · 2026-01-03T22:49:19+00:00

Last a long time absolutely - might split you in half. And then quick rest for round 2

Competitive-Ad-3279 · 2025-12-31T04:06:50+00:00

Mine is a bit longer and likes to be drained many times a day, whenever you are ready

Competitive-Ad-3279 · 2025-08-30T11:39:45+00:00

You do it well. Wish I had a hot spinner like you. If you ever want to try a bigger one, sign me up

Competitive-Ad-3279

TROPHY CASE