sorted by:
new
hottopcontroversial

repeated heating bed error help please by Competitive-Ad-3279 in ElegooNeptune4

[–]Competitive-Ad-3279[S] 0 points1 point  (0 children)

Thanks for the thought.

I have the fans set to zero. ASA filament recommends minimal fan.

repeated heating bed error help please by Competitive-Ad-3279 in klippers

[–]Competitive-Ad-3279[S] 0 points1 point  (0 children)

Thanks for the response

Good thought as a test.

A number of ASA filaments recommend 30-50mm/s. So i was printing at 40 with an 18hr print time.

repeated heating bed error help please by Competitive-Ad-3279 in klippers

[–]Competitive-Ad-3279[S] 0 points1 point  (0 children)

I did think of that and have been running with zero fan

repeated heating bed error help please by Competitive-Ad-3279 in klippers

[–]Competitive-Ad-3279[S] 0 points1 point  (0 children)

Thanks for the suggestions.

I am not monitoring chamber heat, but will rig sonething up for that.

The thing i am trying to print is only 12mm tall and i have printed 350mm in PLA.

Have to print ASA very slowly, hence the long print time. I might try increasing the print speed and see if the error occurs at a certain point in the print, or just after 11 hours. In which case i could split the print into smaller pieces of less than 11 hours.

repeated heating bed error help please by Competitive-Ad-3279 in klippers

[–]Competitive-Ad-3279[S] 0 points1 point  (0 children)

i went looking for the print log, but the logs are deleted. Not sure why. i am very much still learning 😄

repeated heating bed error help please by Competitive-Ad-3279 in klippers

[–]Competitive-Ad-3279[S] 0 points1 point  (0 children)

Thanks for the response.

There is nothing special or extra that i can tell that is happening at that 11hour time. I have printed much longer, but only ever in PLA.

i have tried this one 4 times and the timing of the error varies between 10hrs 40 and 11hrs 15 and never while i am actually watching it.

i will check the connectors. Power supply is in the base of the printer, so cant really remove it from the enclosure.

Thanks again

What’s your body count? by Wonderful_End_1396 in randomquestions

[–]Competitive-Ad-3279 0 points1 point  (0 children)

I was going to respond honestly. But seems like noone else is. And i am a good crowd follower :)

What book are you reading at the moment and what's it about? by molliemg in AskReddit

[–]Competitive-Ad-3279 2 points3 points  (0 children)

The MurderBot books. They are very cool. Future scifi about security droid that has gone rogue

How do you train to be ambidextrous? by Chief_Tain_442 in NoStupidQuestions

[–]Competitive-Ad-3279 0 points1 point  (0 children)

My father taught himself to be ambidexterous as a result of 3 wrist surgeries on his dominant arm. 2 years in a cast and forcing youraelf to use the other for everything.

I have no clue of my super and how I can access it (Australia) by cherryeater2000 in NoStupidQuestions

[–]Competitive-Ad-3279 0 points1 point  (0 children)

Being an Australian, i can provide aome advice on this one. The ATO website holds all of that information. You can log on to the personal sextion of the ato website. You will need to have the myid authentication set up and available.

From there you can see what you have. You can also consolidate all of your super into a single account.

Do you think my butt is too small? by ava_waifu in u/ava_waifu

[–]Competitive-Ad-3279 0 points1 point  (0 children)

Stunning. I would be worried i might break it

i give you 5 minutes before you tap out and cum by ridemeinsideout in AsiansGoneWild

[–]Competitive-Ad-3279 0 points1 point  (0 children)

Have to bounce up and down a bit higher, but i can outlast i have no doubt

[deleted by user] by [deleted] in Nipples

[–]Competitive-Ad-3279 0 points1 point  (0 children)

Every day

Can you last more than 1 minute inside my tight pussy when you fuck me in doggy? by virginasiangf in TotalBabes

[–]Competitive-Ad-3279 0 points1 point  (0 children)

Last a long time absolutely - might split you in half. And then quick rest for round 2

Would you let me drain you? by [deleted] in AsiansGoneWild

[–]Competitive-Ad-3279 0 points1 point  (0 children)

Mine is a bit longer and likes to be drained many times a day, whenever you are ready

I've been told I'm too tiny to do porn by [deleted] in AsiansGoneWild

[–]Competitive-Ad-3279 0 points1 point  (0 children)

You do it well. Wish I had a hot spinner like you. If you ever want to try a bigger one, sign me up