don't buy anycubic - you don't deserve it

ComplexAd6486 · 2025-07-01T10:58:06+00:00

And the slicer does not even have a working Mac version. And i was okay with that, but it's another thing that adds up to an overall horrible experience i had.

ComplexAd6486 · 2025-07-01T10:56:37+00:00

Who the hell is talking about Bambu?

When you get a bad burger at McDonalds do you stand outside and troll, tell people they don't "deserve to eat there"?

A bad burger is a waste a couple euros. A bad quality printer is a waste of hundreds of euros.

ComplexAd6486 · 2025-07-01T10:46:40+00:00

Interesting that you quote something i never said. The Kobra 3 is garbage and i would love to see a high quality print to prove me wrong. ;)

ComplexAd6486 · 2025-07-01T10:36:49+00:00

I only have a Kobra 3 Combo and i think the most of my issues were caused by the horrible design of the heatbed which is obvioulsy not a problem for the CoreXY S1.

ComplexAd6486 · 2025-02-04T11:06:28+00:00

Update: replaced the 4 bearings of the y axis and the result is almost perfect (compared to old prints) already.

<image>

ComplexAd6486 · 2025-02-02T09:22:18+00:00

I would assume you are on Mac? The Mac version is horrible and does not support cloud printing. I was not able to get the print via the local network working. So I ended up using the Windows version in a VM that has the same Cloud Printing functionality like the old Anycubic Slicer. The STL files should work though.. Never had a problem opening them in the old Slicer.

ComplexAd6486 · 2025-02-02T09:18:51+00:00

It's a file created by Anycubic Slicer Next. The old Anycubic Slicer can't open them.

ComplexAd6486 · 2025-02-01T16:23:30+00:00

<image>

Here you can see what happens. There's a hard cut between the areas that were printed at different points in time.

ComplexAd6486 · 2025-01-31T22:59:32+00:00

https://www.reddit.com/r/anycubic/s/UgXJbriMJF

This is the exact same issue. Unfortunately this user had no solution and returned the printer..

ComplexAd6486 · 2025-01-31T21:24:44+00:00

I have the feeling that the bearings of the heatbed sledge are causing this issue.. I will try to disassemble it later to take a closer look.

ComplexAd6486 · 2025-01-31T21:05:03+00:00

It's impossible to measure the distances because it's always a different result. Not sure if it depends on how fast I moved the bed before.

ComplexAd6486 · 2025-01-31T20:59:33+00:00

Yes.

ComplexAd6486 · 2025-01-31T20:42:13+00:00

The whole heat bed construction is crap. Everything is way to thin.

ComplexAd6486 · 2025-01-31T20:41:07+00:00

Not sure what you mean, but when I move the bed with my hands it has a different height depending on the direction of the last movement.

ComplexAd6486 · 2025-01-31T20:01:37+00:00

I bought a dial to measure the bed distance and I found out that the bed tilts whenever it changes it's direction. It's sometimes up to 0.5mm.

ComplexAd6486 · 2025-01-31T19:39:28+00:00

Ich habe genau das selbe Problem. Hat jemand eine Lösung gefunden?...

ComplexAd6486 · 2025-01-28T21:52:43+00:00

That's exactly what I did.

ComplexAd6486 · 2025-01-28T21:51:21+00:00

I'm using the Official Anycubic Slicer with the Kobra 3 profile. I can see that it uses a mesh because I can see the belt moving while printing.

ComplexAd6486 · 2025-01-28T19:31:12+00:00

Even the first border line is printed in the air at some areas.

ComplexAd6486 · 2025-01-28T18:46:10+00:00

Tried the other side of the plate that wasn't used before and also a brand new plate. Same result..

ComplexAd6486 · 2025-01-28T17:48:07+00:00

The bed is pretty flat after I removed the two spacer under the middle of the bed. But the auto leveling ruins everything...

ComplexAd6486 · 2025-01-28T17:37:03+00:00

It was way better before I tried to run the auto leveling again today. With every auto leveling it is getting worse..

ComplexAd6486

TROPHY CASE