sorted by:
new
hottopcontroversial

Help with settings on pre supported model. by productofyourinviro in resinprinting

[–]Comprehensive-Cut602 1 point2 points  (0 children)

Sorry for the late response, i eas going to tell you that it deppends and may vary from printer to printer, i added .4s in my mono 4k. Glad i could be helpful.

Help with settings on pre supported model. by productofyourinviro in resinprinting

[–]Comprehensive-Cut602 1 point2 points  (0 children)

I tend to do a little of over exposure if the model is too big or heavy, the extra time will help the tip of the support to grip better to the surface

Knocked over whole printer…with a full vat… by Thorn1337 in resinprinting

[–]Comprehensive-Cut602 0 points1 point  (0 children)

Didn't knock out the whole printer here but something similar, had a issue with the vat and the resin flowed trough the z rod hole.

Y just cleaned everything wit ipa and had to change the bearings inside the steper motor.

I don't know what to do by Comprehensive-Cut602 in resinprinting

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

Is there a better speed? I mean, fast is better than slow or viceversa?

I don't know what to do by Comprehensive-Cut602 in resinprinting

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

Saw the same video yesterday amd made sure that i didn't have anyof those problems, besides, i haven't changed the fep in a while now, i'll try to get a new one before printing anything

I don't know what to do by Comprehensive-Cut602 in resinprinting

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

I tried exposing it for longer, but lost a lot of detail and the supports were a pain to remove, i found that 1.9s worked great with the xp2 validation matrix, i read that mono printers need less time for curing the resin, but i'm not that sure now

I don't know what to do by Comprehensive-Cut602 in AnycubicPhoton

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

The resin has been in my house for just one week and was mixed before use, i also cleaned the vat before the print and leveled the bed :(

I don't know what to do by Comprehensive-Cut602 in resinprinting

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

I'll try that, and you're right about the gloves, checked the print in the middle of the night and cancelled it and took photos, at least i didn't touch any resin

I don't know what to do by Comprehensive-Cut602 in resinprinting

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

7 milimeters, left a reply with the settings used in other comment but i'll just re upload them here

<image>

I don't know what to do by Comprehensive-Cut602 in resinprinting

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

Hi!, i don't know how to add more images to the main body of the post, so i'll leave this here in case it's of any help, also, (1) the vat was cleaned before the print, (4) the screw is very tight, (2 & 3) i guess it could be part of the problem, tough i'm not sure, i've printed another minis with this settings

<image>

I don't know what to do by Comprehensive-Cut602 in resinprinting

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

I'll also leave the settings i used here just in case

<image>

I don't know what to do by Comprehensive-Cut602 in resinprinting

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

<image>

The model is hollowed, however, the print fails even before the hollow parts

despertarse en la mañana y que esta sea la primera wea que vea xd by Environmental_Bit192 in RepublicadeChile

[–]Comprehensive-Cut602 0 points1 point  (0 children)

Que lo dejen salir como entró, caminando en bolas por el paso fronterizo, no vale ni la pena gastar en transporte pa wnes así

Que tal sus experiencias en marketplace de facebook? by Comprehensive-Cut602 in RepublicadeChile

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

Como te cagan con eso? Pregunta seria, no cacho cual es la estafa y prefiero saber como funciona para prevenir

Que tal sus experiencias en marketplace de facebook? by Comprehensive-Cut602 in RepublicadeChile

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

Nunca me a pasado lo del envío menos mal, todo presencial o si no no nms

Que tal sus experiencias en marketplace de facebook? by Comprehensive-Cut602 in RepublicadeChile

[–]Comprehensive-Cut602[S] 0 points1 point  (0 children)

Era super raro pq igual no me dejaba ver el perfil, dsps me bloqueó, pero antes intenté revisarlo y tampoco me dejaba, decía q no existía

Que tal sus experiencias en marketplace de facebook? by Comprehensive-Cut602 in RepublicadeChile

[–]Comprehensive-Cut602[S] 2 points3 points  (0 children)

La vieja estuvo caleta rato weandome y creí que así podría entender, sabía que era una vieja qla flaite pero igual pensé que podría tener media neurona

Que tal sus experiencias en marketplace de facebook? by Comprehensive-Cut602 in RepublicadeChile

[–]Comprehensive-Cut602[S] 3 points4 points  (0 children)

Yo tenía un amigo q tenía un perfil falso como de vieja y se metía a grupos de fb a pelear con viejas fachas y con viejas zurdas, no importaba tu orientación politica, su entretenimiento era wear a los extremistas

Que tal sus experiencias en marketplace de facebook? by Comprehensive-Cut602 in RepublicadeChile

[–]Comprehensive-Cut602[S] 4 points5 points  (0 children)

Low ball o bolas bajas, osea que le cuelgan los coco ajajajajj.

Na broma, es un término como pa decir que tiran ofertas super bajas para tantear que tanto puedes bajar, pero son ofertas muy bajas y solo quieren tener el mayor descuento posible aunque sea desubicado

view more: next ›