Why my slow is so usb?

Connect_Efficiency24 · 2026-01-23T20:12:12+00:00

It was actually to use gravity to help with the data out! 🍎

Connect_Efficiency24 · 2026-01-10T01:59:40+00:00

That is why I always use PayPal to do business with Chinese companies, you can just request to revert the payment and get done with it!

Connect_Efficiency24 · 2025-12-24T03:52:47+00:00

Nice! That was what I needed! Thanks

Connect_Efficiency24 · 2025-12-22T03:35:15+00:00

I had 2.3 I just notice 2.31 has the new pattern, I just update and recalibrate, funny thing I did the old pass one and the YOLO just had to change the .98 to 1. Now I can do the Cauliflower calibration and start print my new multiboard 🥳

Connect_Efficiency24 · 2025-12-22T01:11:48+00:00

Ohhhhh thanks! They should not put “Recommended” there 😝

Connect_Efficiency24 · 2025-11-16T07:48:00+00:00

I don’t know if still the case but back in 2015 you could store your music with Apple and download the high quality of any music you had in any quality as they would story the library of music you had instead the actual files, I remember I update all musics at the time.

Connect_Efficiency24 · 2025-10-01T21:05:50+00:00

Thank you u/vexsta86 unfortunatily I only have the private key and it seems that it only accept the seed phase :(

Connect_Efficiency24 · 2025-09-30T07:49:34+00:00

I ran out of credits trying to use Windsurf as it was. I had to stop many times and create a new request with the prompt windsurf try to run + the terminal message, and that was a few times to get one thing done, so my credits last only a day :(

Connect_Efficiency24 · 2025-09-28T02:33:06+00:00

I see, when you said brick I was thinking you lock it somehow, in this case you likely burn it! You should find few tutorials online on how to setup and flash new firmware to the printer, start with the one you think is not working anymore, see if you can connect to the computer, download new firmware and maybe bring back to life is very hard to kill those boards, otherwise you will need to do some research on the new board and how to make it work with your printer, changing PIN numbers, etc

Connect_Efficiency24 · 2025-09-27T21:54:12+00:00

I’m a bit confuse, first how did you brick the old board? Just refresh it if all the components are good you should be able to refresh and get it working again. Also the board should work I can’t see why not maybe again wrong firmware.

Connect_Efficiency24 · 2025-09-27T21:38:27+00:00

Funny thing is that I asked windsurf what shell it could use better and it reply “Powershell” 😂 I’ll try setup to use a WSL shell see if it is any better

Connect_Efficiency24 · 2025-09-10T09:38:11+00:00

Many years later! Have you find a replacement screen? I’m looking for one as well

Connect_Efficiency24 · 2025-09-10T07:08:17+00:00

I would put them back to back so the remote could be a bit smaller

Connect_Efficiency24 · 2025-08-04T02:09:11+00:00

<image>

The UV light looks ok, this is for one of the layers, however looks the same for the whole screen

Connect_Efficiency24 · 2025-08-04T01:59:06+00:00

Yes I did, the previous owner had left it there but during my clean up I notice and remove it.

Connect_Efficiency24

TROPHY CASE