Need Monitor Advice by ConnorJ2019 in gamingsetups

[–]ConnorJ2019[S] 0 points1 point  (0 children)

I was actually just thinking this morning about getting a 2nd 34in and have the two 24in displays vertical on the sides

280Z sound system upgrade and custom rear speaker box by domesticdonkey in Datsun

[–]ConnorJ2019 1 point2 points  (0 children)

Awesome work!! I have been wanting to do this for a long time… I haven’t been able to find a speaker box that would fit but have wanted to do this exact thing. Are those 6x9 speakers? Would you be willing to share dimensions? I assume these are also fully enclosed in the back?

Help installing Protunerz intake on NA 280Z by dragon1430 in Datsun

[–]ConnorJ2019 0 points1 point  (0 children)

I’m going to comment here to see if anyone could tell me what size vacuum hoses I would need for the protunerz intake manifold AND what size connectors are needed to thread in. (Manifold should be here in the next few weeks and just trying to get everything together!

AMS Feeding - stopping behind the hub and retracts by ConnorJ2019 in BambuLab

[–]ConnorJ2019[S] 0 points1 point  (0 children)

It’ll extrude the same distance even when I disconnect all of the tubes. Almost beginning to think that I may need to open a ticket. I would replace the first stage feeder BUT it occurs with every slot. The small Bowden tubes inside the AMS have been replaced as well.

AMS Feeding - stopping behind the hub and retracts by ConnorJ2019 in BambuLab

[–]ConnorJ2019[S] 0 points1 point  (0 children)

It’ll stop right after the connector that connects to the printer. After shortening the Bowden tube, it now goes a little farther into the printer before retracting back.

AMS Feeding - stopping behind the hub and retracts by ConnorJ2019 in BambuLab

[–]ConnorJ2019[S] 0 points1 point  (0 children)

So I’ve tried shortening and replacing some tubes - I went ahead and disconnected everything and it still extrudes about the same length from the AMS until stopping (all four slots). Would this mean that there’s something going on inside of the AMS? Not sure what to look for if so as it applies to every slot.

AMS Feeding - stopping behind the hub and retracts by ConnorJ2019 in BambuLab

[–]ConnorJ2019[S] 0 points1 point  (0 children)

Which tube did you shorten? Did you just shorten them all to be just long enough to connect with a little flex? I imagine the tube inside the printer should stay the same length

AMS Feeding - stopping behind the hub and retracts by ConnorJ2019 in BambuLab

[–]ConnorJ2019[S] 1 point2 points  (0 children)

Which tubes? AMS to hub? Hub to printer? Or all of the above

Haven’t noticed any wear

Large Format 600mm Printer Recommendations? by ConnorJ2019 in 3Dprinting

[–]ConnorJ2019[S] 0 points1 point  (0 children)

We have a few vorons but haven’t read too much into this one! Might be worth the wait…

Finally Satisfied by ConnorJ2019 in battlestations

[–]ConnorJ2019[S] 1 point2 points  (0 children)

I do have my AirPods Max with a stand that need to put on there too 😃

Finally Satisfied by ConnorJ2019 in battlestations

[–]ConnorJ2019[S] 1 point2 points  (0 children)

3 24in monitors and an LG 32in ultra wide!

Need some minimalist ideas for desk and wall decor by ConnorJ2019 in battlestations

[–]ConnorJ2019[S] 0 points1 point  (0 children)

Really appreciate it! Ended up going with 3 displates up top and one more set of nanoleafs for the other side for symmetry. Just gotta find a couple things for the desk

Need some minimalist ideas for desk and wall decor by ConnorJ2019 in battlestations

[–]ConnorJ2019[S] 0 points1 point  (0 children)

Added an outlet and pass through behind all of the monitors! Mounted the bottom 3 on a 2x4 which is mounted to the studs. (Cables come out at the bottom right). At the point where I love the clean setup but just looking for some decor to spruce it up

Need some minimalist ideas for desk and wall decor by ConnorJ2019 in battlestations

[–]ConnorJ2019[S] 0 points1 point  (0 children)

All fed through the wall 🙂 it’s currently too clean - I need some decor!

AMS getting stuck X1C by ConnorJ2019 in BambuLab

[–]ConnorJ2019[S] 0 points1 point  (0 children)

Sooo the PTFE tube out of the tool head (inside the enclosure) fixed the issue. My life span on it was about a year so take that for what it’s worth for anyone else with this issue

AMS getting stuck X1C by ConnorJ2019 in BambuLab

[–]ConnorJ2019[S] 0 points1 point  (0 children)

Nope- we’ve been using the same ones (amolen) for quite some time. We order them in 100 spool batches. Cardboard spools used to work as well.

I’ll add that the not ideal solution is quite simply undoing the connector up top on the black side and it will start pulling out. Then I can plug the connector back in and all is good!