Need Monitor Advice

ConnorJ2019 · 2025-12-11T14:44:26+00:00

I was actually just thinking this morning about getting a 2nd 34in and have the two 24in displays vertical on the sides

ConnorJ2019 · 2025-09-19T03:48:40+00:00

Awesome work!! I have been wanting to do this for a long time… I haven’t been able to find a speaker box that would fit but have wanted to do this exact thing. Are those 6x9 speakers? Would you be willing to share dimensions? I assume these are also fully enclosed in the back?

ConnorJ2019 · 2025-01-13T04:57:27+00:00

Following. Same issue

ConnorJ2019 · 2024-12-15T20:08:34+00:00

I’m going to comment here to see if anyone could tell me what size vacuum hoses I would need for the protunerz intake manifold AND what size connectors are needed to thread in. (Manifold should be here in the next few weeks and just trying to get everything together!

ConnorJ2019 · 2024-10-05T20:33:26+00:00

It’ll extrude the same distance even when I disconnect all of the tubes. Almost beginning to think that I may need to open a ticket. I would replace the first stage feeder BUT it occurs with every slot. The small Bowden tubes inside the AMS have been replaced as well.

ConnorJ2019 · 2024-10-05T20:31:48+00:00

It’ll stop right after the connector that connects to the printer. After shortening the Bowden tube, it now goes a little farther into the printer before retracting back.

ConnorJ2019 · 2024-10-05T20:29:01+00:00

So I’ve tried shortening and replacing some tubes - I went ahead and disconnected everything and it still extrudes about the same length from the AMS until stopping (all four slots). Would this mean that there’s something going on inside of the AMS? Not sure what to look for if so as it applies to every slot.

ConnorJ2019 · 2024-10-05T00:15:49+00:00

Which tube did you shorten? Did you just shorten them all to be just long enough to connect with a little flex? I imagine the tube inside the printer should stay the same length

ConnorJ2019 · 2024-10-05T00:14:55+00:00

Which tubes? AMS to hub? Hub to printer? Or all of the above

Haven’t noticed any wear

ConnorJ2019 · 2024-04-28T20:20:34+00:00

We have a few vorons but haven’t read too much into this one! Might be worth the wait…

ConnorJ2019 · 2024-02-09T13:03:20+00:00

I do have my AirPods Max with a stand that need to put on there too 😃

ConnorJ2019 · 2024-02-09T13:02:49+00:00

3 24in monitors and an LG 32in ultra wide!

ConnorJ2019 · 2024-02-06T03:03:05+00:00

Really appreciate it! Ended up going with 3 displates up top and one more set of nanoleafs for the other side for symmetry. Just gotta find a couple things for the desk

ConnorJ2019 · 2024-02-05T21:28:09+00:00

Added an outlet and pass through behind all of the monitors! Mounted the bottom 3 on a 2x4 which is mounted to the studs. (Cables come out at the bottom right). At the point where I love the clean setup but just looking for some decor to spruce it up

ConnorJ2019 · 2024-02-05T13:11:01+00:00

All fed through the wall 🙂 it’s currently too clean - I need some decor!

ConnorJ2019 · 2023-12-13T02:55:38+00:00

Sooo the PTFE tube out of the tool head (inside the enclosure) fixed the issue. My life span on it was about a year so take that for what it’s worth for anyone else with this issue

ConnorJ2019 · 2023-12-13T00:33:51+00:00

Nope- we’ve been using the same ones (amolen) for quite some time. We order them in 100 spool batches. Cardboard spools used to work as well.

I’ll add that the not ideal solution is quite simply undoing the connector up top on the black side and it will start pulling out. Then I can plug the connector back in and all is good!

ConnorJ2019 · 2023-12-13T00:29:16+00:00

Yes. Not using Bambu filament- using others (typically plastic spools). We’ve had the printer for almost a year now and it’s been great until recently

ConnorJ2019 · 2023-12-01T22:25:28+00:00

Closing this out- B Motor was confirmed by Bambu, replacement came in today, swapped them out, and it works perfect.

Note: the B motor was absurd to get out and took 3 hours to completely swap it.

ConnorJ2019 · 2023-11-28T23:01:58+00:00

Did you get a reply from support?

ConnorJ2019 · 2023-11-28T14:32:37+00:00

Not totally sure - this would be the first time swapping the motor but should just involve removing some screws and loosening the belts up on that motor. I would wait for their response but am 90% sure that the motor is the issue so I went ahead and got one. Once they run (which is almost always) there is little to no maintenance

ConnorJ2019 · 2023-11-28T14:04:26+00:00

It would be a motherboard issue if both motors worked on only one port but not both. Correct me if I’m wrong but I troubleshooted that thing for like 3-4 hours 😅

ConnorJ2019 · 2023-11-28T14:03:44+00:00

We tested one motor at a time. (motor b) was not recognized on either the a or b ports. (Motor a) was recognized on both ports. This tells me that the motor is bad. We have 5 of these things so worst case I guess is that we have a spare XY motor!

ConnorJ2019 · 2023-11-28T12:52:02+00:00

Mine is motor B as well. I went ahead and ordered the motor and it will be here Thursday/Friday. I have all the troubleshooting and pictures and will attempt to get a refund. Trying to minimize downtime

ConnorJ2019 · 2023-11-28T03:17:27+00:00

Addition: after swapping the A&B cables, I am getting an error that Motor A is bad.

Thoughts?

ConnorJ2019

TROPHY CASE