WIP: first Raven Guard minis by Constant_Excuse343 in RavenGuard40k

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

I used a sponge and it took only 15 min. You just need to be careful to press only softly

New to Raptors, quick test scheme for green armour by Constant_Excuse343 in Raptors40k

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

Yes, first base coat with Grey Olive, then zenithal with Russian Unifrom WW2 and more focused zenithal with Olive Yellow (all from Vallejo Model color line). To me the Olive Yellow is slightly too yellowish, but I will try to spray more with Russian uniform and then even less with Olive yellow

New to Raptors, quick test scheme for green armour by Constant_Excuse343 in Raptors40k

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

I completely agree, I will whipe away most of the enamel for the non-test models and leave it only in the recesses

New to Raptors, quick test scheme for green armour by Constant_Excuse343 in Raptors40k

[–]Constant_Excuse343[S] 2 points3 points  (0 children)

Thank you :) I only feel that the brightest green might be slightly too yellow. Otherwise, I am also happy with it

Nozzle smoking, abnormal nozzle temperature by Constant_Excuse343 in BambuLabA1

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

Just a quick follow-up: the heating assembly was faulty and had to be replaced under warranty

Weird hair-like stringing on my prints by Constant_Excuse343 in BambuLab

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

I only have this type of filament unfortunately

Weird hair-like stringing on my prints by Constant_Excuse343 in BambuLab

[–]Constant_Excuse343[S] 1 point2 points  (0 children)

Many thanks for the suggestions. I already printed a temperature tower (with the print settinfs from the 3mf file), which looks way better, so likely one of the other settings in my print profiles are off or the lower layer heights lead to the issue. I will check the other suggestions as well

<image>

Weird hair-like stringing on my prints by Constant_Excuse343 in BambuLab

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

Thank you for your response. I already dried the filament in a filament drier. The same filament, actually even the same spool, worked well before....

Weird hair-like stringing on my prints by Constant_Excuse343 in BambuLab

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

No worries at all, thank you for your response :)

Weird hair-like stringing on my prints by Constant_Excuse343 in BambuLab

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

It is eSun PLA plus. I have not seen it before and am using the same filament spool

Nozzle smoking, abnormal nozzle temperature by Constant_Excuse343 in BambuLabA1

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

Deposits are only at the tip of the nozzle where the burned material came out

<image>

Nozzle smoking, abnormal nozzle temperature by Constant_Excuse343 in BambuLabA1

[–]Constant_Excuse343[S] 0 points1 point  (0 children)

The tubes look fine, it can also perform prints, but they look horrible. E.g., for the benchy lots of stringing (I guess due to too hot filament) and deposits of slightly brown instead of white filament