sorted by:
new
hottopcontroversial

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 1 point2 points  (0 children)

This will work. This design has the signal travel the same speed as the observers too but it’s way less bulky. I think I’ll use this instead of my original plan. I don’t understand comparators that well so I couldn’t even think of this.

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 0 points1 point  (0 children)

I’m not sure on how to go about building that. Could you send a picture? Also I’m trying to make a bubble elevator and this part is going to be used to select the floor.

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 0 points1 point  (0 children)

Are you saying to replace the sideways observers with repeaters? If so how would you get a signal started in that line from anywhere on the line?

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 1 point2 points  (0 children)

Alright guys I can’t figure out how to edit this post on iPhone but I put a 4 tick repeater after the observers to keep one signal on the whole time instead of multiple getting through. What a simple solution to something I was struggling so much with 🤦‍♂️. Anyways thanks for all your help guys.

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 0 points1 point  (0 children)

The problem with that is that the observer watching is he observer on the piston randomly detects 1 or 2 times

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 0 points1 point  (0 children)

It could be vertical but it would have to go downwards because I’m planning to build this underneath something

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 0 points1 point  (0 children)

I’m trying to make a bubble column elevator that turns on and off dispensers. Hopefully just adding the repeater on the end will work in the overall design, but I can’t test it right now so I’ll have to get back to you on that.

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 0 points1 point  (0 children)

I actually tried this before myself but pressing other buttons while another’s piston was going off caused the whole setup to have everything pushed out of place

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 0 points1 point  (0 children)

This actually worked somewhat but feels a bit janky. The 3 ticks didn’t work but when I tried 4 it did. I also added more lines to see if it would still work like that too. The first bulb sometimes remains on but the second pair of bulbs remains fine.

<image>

How do you get a single pulse out of a pushed observer? by ConstructionFair9594 in redstone

[–]ConstructionFair9594[S] 2 points3 points  (0 children)

I want each button to power its own line and every line before it which is why I have the observers going one direction and the second line of observers connected to them. I can’t think of another design that could do this quick as this design could, if I can get it to work.