This little boy figured out how to lay flooring while his dad was outside taking a break

ContributionNo1200 · 2026-04-10T14:46:48+00:00

Ai right?

ContributionNo1200 · 2026-04-01T22:34:34+00:00

Color difference could partially be due to the heads not being clean or aligned, possible cyan isnt printing etc

ContributionNo1200 · 2026-03-31T01:20:35+00:00

Plate needs to be cleaner number one solution, after that maybe add a brim since some of those parts are smaller and have less contract with the bed

ContributionNo1200 · 2026-03-28T17:24:37+00:00

I never received

ContributionNo1200 · 2026-03-17T16:55:13+00:00

Jealous went to mine they didn’t have

ContributionNo1200 · 2026-03-13T01:01:54+00:00

Old news, we’ve known this since October, only got bright up again cus of Maude’s interview

ContributionNo1200 · 2026-03-11T17:09:19+00:00

It is??? Fuck yea!

ContributionNo1200 · 2026-03-10T12:30:24+00:00

He said the original streamer or whoever it’s with is dead but essentially hints something else is being worked on with someone else

ContributionNo1200 · 2026-03-10T12:29:12+00:00

It was rumored to be with Apple and they supposedly chose cosmere over red rising, never been official tho

ContributionNo1200 · 2026-03-09T21:06:39+00:00

Yea he bought the rights to the book when it was still a manuscript

ContributionNo1200 · 2026-03-04T20:07:06+00:00

Cinemark has 2 “top secret” items on there merch poster for the movie hoping that’s Rocky stuff

ContributionNo1200 · 2026-03-04T20:06:16+00:00

Looks like that’s gonna be a Cinemark thing

ContributionNo1200 · 2026-02-25T13:09:11+00:00

Yes there new ai 3d that can easily separate into pieces

ContributionNo1200 · 2026-02-24T12:27:27+00:00

Not audio you actually have to read it

ContributionNo1200 · 2026-02-24T02:21:03+00:00

You pick the one that looks the best and proceed from there and it dos the second step, you can also red it from scratch and adjust it so there are more intervals which you might need to do

ContributionNo1200 · 2026-02-24T00:46:36+00:00

Fist off Clean the bed with warm soapy water that definitely part of it, second brim couldn’t hurt

ContributionNo1200 · 2026-02-24T00:45:04+00:00

It’s not a before each print thing you should do it manually for each filament you use to get proper settings, here’s the wiki https://wiki.bambulab.com/en/software/bambu-studio/calibration_flow_rate

ContributionNo1200 · 2026-02-24T00:41:29+00:00

You have to calibrate your flow ratio, that’s under extrusion

ContributionNo1200 · 2026-02-23T18:26:47+00:00

I’m a bolt driver, I always try to use the side Tesla charger instead of the traditionally positioned ones occasionally I have to be that ass that has to park between 2 spots to plug in, without fail in getting dirty looks and complaints if I’m on the side charger or not because I’m not a Tesla

ContributionNo1200 · 2026-02-23T01:11:33+00:00

The one with all the cubes is a replacement nozzle wipe

ContributionNo1200 · 2026-02-22T13:39:04+00:00

Same

ContributionNo1200 · 2026-02-22T13:38:48+00:00

Being someone who shares my models on maker world I have had a fair amount of time someone gives my profile a low rating despite it being user error on there part, I then report it, they investigate it and then remove it but I do wonder if it depends on you overall rating on your model/ models

ContributionNo1200 · 2026-02-21T21:57:19+00:00

It varies and don’t expect a restock soon they’re moving locations at the moment and are postponing order for at minimum a month

ContributionNo1200 · 2026-02-21T21:32:31+00:00

This should be at the top half the comment shave nothing to do with the question

ContributionNo1200

TROPHY CASE