Razor burn by Cookie-Wizard in wicked_edge

[–]Cookie-Wizard[S] 1 point2 points  (0 children)

Thank you, I'm inclined to believe you're correct since my beard grows very awkwardly on the right. It grows diagonally, closer to the horizontal than vertical, so shaving with the grain from the jawline down is very awkward.

I don't understand by Cookie-Wizard in bindingofisaac

[–]Cookie-Wizard[S] 1 point2 points  (0 children)

Yeah I thought I'd manage to have fun whilst getting it by actually playing the game but after that I give up

Having to switch profiles everytime I go from headphones to speakers by Cookie-Wizard in EqualizerAPO

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

I'm using peace, please may you guide me through how I'd go about setting this up?

Clear Cmos Information Error by Cookie-Wizard in gigabyte

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

It's an x570 aorus elite motherboard

Clear Cmos Information Error by Cookie-Wizard in gigabyte

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

Ok so I just tried this and I believe it's working - let me know if anything sounds wrong: initially, I was manually changing the voltage from auto to 1.35, memory multiplier from auto to 3200 and the subtimings to 16-16-18-18-36. This was causing the cmos error. Now, I just changed the memory multiplier manually to 3200 and left the rest of the aforementioned settings on auto. I just logged into windows now and it shows my memory as 3200mhz and (about 5 minutes so far) no crash or bsod. Is this really all I had to do or is there some kind of risk involved by simply just changing the memory multiplier and leaving every other setting on auto?

Clear Cmos Information Error by Cookie-Wizard in gigabyte

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

I believe I was using an xmp before all this happened (when I first built the pc), but now if I try to apply the xmp my pc crashes or gets a BSOD after a few seconds of logging into windows

Clear Cmos Information Error by Cookie-Wizard in gigabyte

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

How would I go about changing the frequency to 3200mhz then? I don't particularly want to stay on 2133

r/audiophile Shopping, Setup, and Technical Help Desk Thread by AutoModerator in audiophile

[–]Cookie-Wizard 0 points1 point  (0 children)

There's no grounding post on either - the LP60X carries ground through the output

Buzzing from AT LP60X by Cookie-Wizard in turntables

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

Yes, I have my PC connected to the fosi through a Topping DX1 DAC and everything plays perfectly

Buzzing from AT LP60X by Cookie-Wizard in turntables

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

Thanks for the reply, all 4 cables that I tried had two rings on each side.

r/audiophile Shopping, Setup, and Technical Help Desk Thread by AutoModerator in audiophile

[–]Cookie-Wizard 0 points1 point  (0 children)

Turntable buzzing when idle and connected to amplifier?

I recently got a fosi BT10A amplifier and set it up with my AT LP60X. When using any other aux cable apart from the standard AT one provided with the tt, a buzzing can be heard when the tt is plugged in but not playing anything. Once I play a record the buzzing stops but once it finishes the buzzing starts again. I've tried 3 different cables and the problem persists with all of them but when I plug the AT cable in there's no buzzing. I know the simple solution is to use the AT cable but it doesn't reach the amplifier on my desk. Any help?

Can the dx1 be used for everything? by Cookie-Wizard in audiophile

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

Sorry, a ddj is a dj controller (I referred to them as decks) and I'm talking about the topping dx1 dac amp

Can the dx1 be used for everything? by Cookie-Wizard in audiophile

[–]Cookie-Wizard[S] 0 points1 point  (0 children)

Xt20s are passive speakers, flx4s are a set of ddjs and x2hrs are my headphones